Q1. For the single-phase half-wave controlled rectifier with a firing angle of (a = 60°) and with R-L load circuit shown below, draw the output voltage and current waveform. a. Find the extinction angle (B) and conduction angle (8). b. Determine the ripple factor. a = 60° io R = 602 27 ot Vs = v2 240 sin 1207tt Vo 200mH

Q1. For the single-phase half-wave controlled rectifier with a firing angle of (a = 60°) and with R-L load circuit shown below, draw the output voltage and current waveform. a. Find the extinction angle (B) and conduction angle (8). b. Determine the ripple factor. a = 60° io R = 602 27 ot Vs = v2 240 sin 1207tt Vo 200mH

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In a full wave bridge rectifier, the transformer secondary voltage is 20sinwt. The forward resistance of each diode is 20N and load resistance is 1.5K. Calculate, i. Im ii. Ide
A certain unfiltered center-tapped full wave rectifier is powered by a 120 Vrms, 60 Hz power system. The peak value of the output voltage under loaded conditions is 30 V. The capacitance value is 2000 uF, load current of 2A, determine the following: 4. DC load voltage Ripple factor C.
Design a single-phase full wave bridge rectifier with input voltage of 100v and inductive load of 10ohm and 40mH a. Show the waveform relation between the I/P and O/P b. Calculate the average O/P voltage c. Calculate the rms current
A 60 Hz sinusoidal voltage with an RMS value of 120 V is applied to a single-phase full-wave SCR rectifier. The DC output voltage of the rectifier is 101 V, the firing angle (in degrees) of SCR is would be: O A. 36 O B. 45 O C. None of the other choices are correct O D. 30 O E. 60
In the given Full Wave Center tapped Rectifier circuit, a step down transformer gives an RMS voltage as 110V/11-0-11 V is used with R₁ = 1 KQ. Assume diode as Germanium. D₁ a) Find Input Voltage Vin b) Find Peak Output Voltage. c) Find Average Output Voltage. d) Find Current through the load resistor. •ooooo 00000 CT 20-S D₂ R₁
The single phase diode rectifier has a purely resistive loadof R ,Determine 1. The efficiency 2. The form factor 3. The ripplefactor
Question-1: Consider the circuit in Figure below. 1. What type of circuit is this? 2. What is the total peak secondary voltage? B. Find the peak voltage across each half of the secondary. 4. Sketch the output voltage waveform across R1. 5. Sketch the voltage through D1? 6. What is the PIV for each diode? 120 V rms D2
A certain unfiltered center-tapped full wave rectifier is powered by a 120 Vrms, 60 Hz power system. The peak value of the output voltage under loaded conditions is 30 V. The capacitance value is 2000 uF, load current of 2A, determine the following: Peak to peak ripple voltage RMŞ ripple voltage 4. а.
PARALLEL DIODE CONFIGURATION ( NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE).
The average output voltage for a single phase half wave rectifier for the input sine wave of 200sin100 nt Volts is calculated as a. 63.661V b. 57.456V c. 75.235V d. 60.548V
Calculate the theoretical output DC voltage of the center-tapped full-wave rectifier circuit and compare it with measured value. For the capacitive filter, obtain the theoretical values of the DC output voltage and the ripple voltage and compare these values with the measured quantities. Determine also the practical and theoretical values of the ripple factor.
A sine voltage trace displayed on a screen is shown in figure. The x axis is 1unit=40 ms and y axis is 1 unit=4 v; determine the frequency of the sine wave and plot the waveform if the same is applied to input of a full wave rectifier.