Q1. Find the ZT at longitude 175° 38'W given that LMT = 22-42-00 on the 2nd October 2015. Q2. Find LMT at Oslo (10° 43'E) when

Q: Steps y(t) = sin(tr(t)) y(t) = (3 – 2i)r(1– t) y(t) = S r(7)e(-(t-r))

A:

Q: The op-amp shown in the following figure has R1 = R2 = R3 = 100 2 Rf = 1 k2, and V1 = V2 = V3 = 50…

A: Given: In this question, the given details are, The given op-amp figure is, And the given values…

Q: Example 1: n the power system shown, bus 1 is a slack bus with V, = 1Z0° per unit and %3D us 2 is a…

A: The solution can be achieved as follows.

Q: Determine the average power that is being supplied or absorbed at each element. R, +, R$2052 100°…

A: In an AC circuit, the average power is only consumed by resistor in the AC circuit and the average…

Q: 3. Consider the discrete-time sinusoid x[n] = sin (™). a. Plot x[n] for n = 0, ..., 48. b. Is this…

A: Given Data:A discrete-time sequence of,To Find:Plot of the sequence for n=0 to 48.Period.Frequency…

Q: 4. In Figure 4, the input signal results in a base current of 10 mA peak and choose any value of Rc…

A:

Q: For the circuit below, determine the MAGNITUDE of the CURRENT passing through each resistor. R₁ V₂…

A:

Q: Convert the following (Show work!) a) 37₁0 Binary -> →→ b) 1110₂-> Dec c) EA₁ --> Binary 16 d) 4158…

A: Converting any number into decimal number system . Sum of invidual digits with product of respective…

Q: 3. For the A-connected load in the following figure, calculate a) The magnitude and angle of each…

A:

Q: Consider the bridge network shown in Figure 2.1. Find the Thévenin equivalent resistance across the…

A:

Q: 5.1-1 Sketch vEM ) and gn(1) for the modulating signal m(t) shown in Fig. PS.1-1, given , = 10°, k =…

A: The modulating signal is shown below, Here,ωc=108kf=105kp=25

Q: 5.4-2 A periodic square wave m(1) (Fig. P5.4-2a) frequency-modulates a carrier of frequency f. = 10…

A: A periodic square waveform m(t) is shown below, Here,The carrier frequency is,fc=10kHzThe frequency…

Q: A wave is traveling in the positive z direction with frequency = 1 MHz, and wave phase velocity of…

A:

Q: 5.1-2 A baseband signal m(t) is the periodic sawtooth signal shown in Fig. P5.1-2. Sketch oEM() and…

A: A baseband signal is a signal in which frequency ranges are low as compared to a broadband signal.…

Q: 9. The input voltage for the circuit in Figure 1 is shown in Figure 2. L=1 H V;(t) e R= 1 Olun Vo(t)…

A: Transfer function:  The ratio of the Laplace transform of output to the Laplace transform of input…

Q: 13) Simplify the following Boolean function F, together with the don't-care conditions d, and then…

A: We need to simplify the given Boolean function

Q: (a) For the circuit shown in Figure 3.1, what is the time constant, r? t=0 10 ko 3 kN 3 μ 10 V…

A:

Q: a. A laser has a power output rated 450 mW. If this laser were projected onto a circular spot with a…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Add face 00010011 0 0 10 1011 Sum HOME THEAT DÅP M

A:

Q: 2. Find the value of Rs to obtain a voltage gain of 3 for the network in Figure 2. Choose any value…

A:

Q: A parabolic antenna has an opening of 15 m and receives in the normal direction a linearly polarized…

A: Given: Amplitude of radio signal, E0=4×10-7 V/m Antenna opening i.e. diameter, d=15 m Assume antenna…

Q: 5.2-7 Given m(t) e-, fe = 104 Hz, kf = 6000x, and k, = 8000x. %3D %3D %3D %3D (a) Find Af, the…

A: Initially, the bandwidth of signal is to be found. Later, based on modulation index value, bandwidth…

Q: 8 gurban setk Ex. 509. A PID controller has a test input signal: Unit Impulse. Determine the…

A: We need to find out the output for a PID controller for given input .

Q: 21. Which is not a correct attribute of the optocoupled relay circuit shown (a) it is possible to…

A: According to the question, 21. Which is not a correct attribute of the optocoupled relay circuit…

Q: Q3) For the circuit shown in figure below, at V(0) = lv and a) Find the initial value of currents in…

A: "Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: A signal x[n] having the DT Fourier Series (DTFS) coefficients Co = 3 C1 = C2 = 5 C3 = 2-j 2+j is…

A: An input signal x[n] having the DT Fourier Series (DTFS) coefficients are given…

Q: Write expressions (do not sketch) for PM() and PM(t) when A 10, . =10, k 1000, and k, = 1. For…

A:

Q: 4. For the circuit in Figure 7, calculate the a. Number of nodes, branches and meshes b. Value of lo…

A:

Q: A thin, insulating rod of length I carries a linear charge density ^(x) that varies with distance…

A: Electric Field Intensity (Electric force)- kqλ∫ab1R2dR Linear Charge Density- it is the Quantity…

Q: Q4) Design an RLC parallel circuit whose output is a pure sinusoidal, and write the mathematical…

A: Parallel RLC will behave as the resistive circuit at the resonance frequency. At the resonance…

Q: What is the pitch of the thread called out by the thread note illustrated below? 9/16 -9/16-12UNC-2A…

A: Thread note is given it is asked to find the pitch of the thread

Q: +Vcc QUESTION.2. For the power amplifier of figure, if C1 = C2 = 100 µF, R1 = R2 = R3 = 100 N, R1 =…

A: Note: We are authorized to answer three subparts at a time since you have not mentioned which part…

Q: *7. Write the mesh equations for the networks in Fig. 17.65. De- termine the current through the…

A: Applying KVL in loop 1 E1=4+3j…

Q: In the circuit, v(t) = 10cos (400t + 30°) and i(t) = 5cos (400t), find ve(t) and i̟(t). RI Ve 10s R2…

A: Fig: Given circuit  Given that  v(t)=10cos(400t+30°)  Volt =…

Q: The switch in the circuit has been closed for a long time and is opened at t-0. Find vc(t) for t>0…

A:

Q: Point charges 1 mC and -2 mC are located at (3, 2, - 1) and (-1,-1, 4), respectively. Calculate the…

A:

Q: b. For the circuit shown in Figure 2, i. Obtain the value of the currents ia and i, and voltage vo.…

A:

Q: 8. Consider the LTI system described by the block diagram in differential form : yit) 2 -5 -4 If the…

A: Given :

Q: What is the power required in an electrical circuit with a current of 2A and a resistance of 47…

A: NOTE: We are authorized to answer the first question since the exact one wasn’t specified. Please…

Q: Apply nodal analysis to find the power generated by the independent source 2A 4) V. 20 2 0.2V, 102 O…

A:

Q: : Closed-loop transfer function of a unity-feedback Y(s) 07/ R(s) s² +2500s +a system is given by…

A:

Q: Assignment: Find two possible magnitudes of the voltmeter reading shown in the figure if X = 1000, R…

A: The solution is given below

Q: Rs - 10 mH. ASsume an input frequency of 1000 Hz. Z is replaced with R-1000 2, C-1 uF, and L 1.…

A: Calculate the resistance after the source voltage is applied. R=1000 Ω

Q: Q4/ Reduce the number of states in the following state table, and tabulate the reduced state table:…

A:

Q: Consider the circuit shown in Fig. 3.11a s determine all node voltages and branch currents.

A: