Q1. Explain use of Shaft and its types. Q2.Explain Design Procedure of Shaft Subjected to twisting Moment only. Q3.A line Shaft rotating at 200 rpm is to transmit 20 kW. The shaft may be assumed to be made of mild steel with an allowable shear stress of 42 MPa. Determine the diameter of the shaft, neglecting the bending moment on the shaft.

Q1. Explain use of Shaft and its types. Q2.Explain Design Procedure of Shaft Subjected to twisting Moment only. Q3.A line Shaft rotating at 200 rpm is to transmit 20 kW. The shaft may be assumed to be made of mild steel with an allowable shear stress of 42 MPa. Determine the diameter of the shaft, neglecting the bending moment on the shaft.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please answer complete
a: What is the magnitude of torque applied to the shaft? b: The magnitude of the Polar Moment of Inertia of the shaft cross-section? c: The magnitude of the shear stress at r=0in (center of shaft) is?
x Question: The diameter of shaft used in the below design is 90 mm. Identical pulleys are used in the design with a radius of 160 mm. The forces acting on the system are defined as follow: F₁ = 1P kN; F₂ = 8P kN; F3 = 2P kN; F₁ = 6P kN; F5 = 4P kN; F = 7P kN. Employing the maximum shear stress theory, calculate the maximum permissible P for a safe design experience. L₁ = 1.4m; L₂ = 1.8 m; L3 = 1.4m; L4 = 1.6 m; allow = 75 MPa (allowable strength, σs) A F₁ F₂ L2 m F4 B 3 F6 Fs
The outside diameter of a hollow shaft that is twice its inside diameter .what is the ratio of its torque carrying capacity to that of a solid shaft of the same material and the same outside diameter?
Part A A shaft is made of an aluminum alloy having an allowable shear stress of Tallow = 104 MPa. (Figure 1) The diameter of the shaft is 115 mm. Determine the maximum torque T that can be transmitted. Express your answer to three significant figures and include appropriate units. HA T = Value Units Submit Request Answer Part B Figure 1 of 1 What would be the maximum torque T' if a 75-mm-diameter hole were bored through the shaft? Express your answer to three significant figures and include appropriate units. .T µA ? T' = Value Units
es/ EN6902 / General / Final Exam A Wind Turbine has a maximum output of 2MW at a speed of 20 rpm. A shaft of length 2m made of EN8 steel (properties given in the table below) is to transfer torque from the propeller to the turbine. Using a design stress for EN8 Shafting as 240 MPa. You are to: Calculate the diameter size of a solid shaft in mm, so that it will not fail due to torsion. EN8 Shafting Steel Ultimate tensile stress 850 MPa Ultimate shear stress 490 MPa Tensile Yield stress 530 MPa Shear Yield stress 300 MPa Young's miodulus Modulus of rigidity 210 Gpa 78 GPa Select one: O a. 270 O b. 136 O c. 135 O d. 272 SW
Please design the following mechanical shaft targeting design objective of reliable structure and performance via design iterations with constrains of geometrical dimensions within performance requirement, safety, and economic factors (finding minimum material cost of suitable diameter). Notes: This shaft is transmitting 200 kW at 1200RPM. Please design the shaft with a suitable diameter via iterations, if the maximum torque transmitted exceeds the mean by 30%. Take maximum allowable shear stress as 70 MPa.
1. A 50-mm diameter solid shaft, with a length of 1 meter, is supported at one end and free in the other end. Determine the maximum allowable torque for each material if the angle of twist is not to exceed 6º. Remember to consider both the maximum shear stress and the angle of twist. MATERIAL MODULUS OF RIGIDITY MAXIMUM SHEAR STRESS TORQUE Aluminum 26 GPa 207 MPa Steel 79 GPa 75 MPa Titanium 44 GPa 760 MPa
I need Question 5.2.3 &5.2.4
400 lb-in. 1200 lb-in.. Specifications: Shafts AB, BC, CD are solid material. 500 lb-in., B AB=0.6 in. C dsc-0.75 in. dcp = 0.9 in. Determine: a) The shaft section in which the maximum shear stress occurs and the magnitude of the stress. Now consider that the shaft is tubular with a 0.300 inner diameter. Determine: b) The shaft section in which the maximum shear stress occurs and the magnitude of the stress.
Two designs for a shaft are being considered. Both have an outside diameter of 70 m and are 900 mm long. One is solid but the other is hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Compare the torsional shear stress, angle of twist of the two designs if they are subjected to a torque of 796 N. m.
5- Please I want answer of this question. Thanks