Q1. Answer/Interpret the following:C-142HHHSHUNT FIELD11mm!?A1AZARACR-1STOPSTARTC₂Co-3CR₂o1. Objective of this controller:2. If stop is pressed and CRD-1 remains open, explain and fix the issue.3. Start pressed and the Motor over speeds,, explain and fix the issue.4. Start pressed and the Motor Jogs: Fix this issue5. Effect of Resistance

1. Objective the given controller is The circuit opens the engine and the green light OPENs when the…

Answered: Q1. Answer/Interpret the following:…

Q1. Answer/Interpret the following: Cp-142 HHH START Cp-3 1. Objective of this controller: STOP SHUNTFIELD "mm"? CR-1 CR₂)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

J1. What are the standard identification letters for the shunt field winding of a DC compound motor? a) A1 and A2 b) S1 and S2 C) F1 and F2 d) none of the above J2. The commutating field is another term for interpoles. a) true b) false J3. What are the standard identification letters for the commutating field winding of a DC compound motor? a) C1 and C2 b) S3 and S4 c) either "a" or "b" d) neither "a" nor "b"
The following information is given for a 300kW, 600V, long shunt compound DC generat or, shunt field resistance is 75 ohms, armature resistance 0.01, brush resistance is 0.011 ohrms, series field resistance is 0.012 ohms and the divert or resistance of 0.036 ohms.When the machine is delivering full load; a. Draw the circuit diagrarn b. Calculate the voltage and C Power generated by the armat ure.
Q1/A) Fill in the following blanks 1. The air gap between stator and rotor is about...mm Pe 2. The iron losses are depending on ..sker,.eddcon 3. The relationship between stator and rotor current frequency is 4. The range of operation mode slip is ..... 5. The relationship between hysteresis loss and frequency is .... 23 kT ri
Please choose the correct answer for question number 16. EXPLAIN BRIEFLY why it is the correct answer. Thanks!
Please choose the correct answer for question number 13. EXPLAIN BRIEFLY why it is the correct answer. Thanks!
write true or false in the following sentences: 1. Load torques which always oppose the motion and change their sign on the reversal of motion are called passive load torques. 2. The control rectifier drive has low atmature current ripple compare to de to de chopper drives. 3. The main difference between dynamic breaking and regenerative braking of de motor is the disconnection the source from de motor in dynamic braking. 4. Two quadrant operation of de motor can be obtained from thee phase semiconverter. 5. de-de four-quadrant drives can be supply high power than ac-de four-quadrant drives.
Help me solve this one
There may be more than one answer
Q4/ Chose the correct answer for the following 1. In BLDC motor field winding is kept on a) Stator b) Rotor c) Can be placed anywhere d) Absent 2. By electronic circuitry BLDC can be controlled for both constant and variable torque operation. a) True b) False 3. In medical fields which DC motor is widely used? a) PMDC b) BLDC 4. Construction of BLDC is exactly similar to the a) Conventional DC motor c) Permanent magnet synchronous motor b) Induction motor 5. Typical brushless motor doesn't have a) Commutator b) Permanent magnet 6. The sensor most commonly used in the BLDC motor is a) Thermo Sensor b) Relay Sensor c) Brushed DC motor d) Cannot be determined d) Totally different construction c) Electronic controller d) Fixed armature c) Hall Sensor d) Power Sensor
9-In a the shunt field winding is connected in parallel with the armature winding only. Ish Series . Field EJR Shunt Rsh Rse Field 10-The consist of and 11- E = (V – IaRa ) then N = LOAD
A de shunt motor operating unloaded at a terminal voltage of 125V at a speed of 1420 rpm. When the motor is operated unloaded at the same terminal voltage but with an additional resistance of 8n in series with the shunt field, the motor speed is 1560rpm. (Ignore armature reaction and magnetic saturation) a) Calculate the resistance of the shunt field. b) Calculate the motor speed if the series resistance is increased from 80 to200. c) With the field resistance at its original value and no series resistance, calculate the motor speed if it is operated loaded at a terminal voltage of 90 V and a teminal current of 100A.
Electrical engineering subject of electrical machines/ I need a correct and accurate solution