Q1. A 50 lb beam is supported by a pin support and a spring. If the original length of the spring is 2 ft, determine the magnitude of the force need to be applied at point B and the horizontal and vertical reactions at A to hold the beam in a horizontal position. (hint: What is the length of the spring now if the beam is in a horizontal position?) 3 ft A k = 100 lb/ft mmmmmmm 3 ft F B

Q1. A 50 lb beam is supported by a pin support and a spring. If the original length of the spring is 2 ft, determine the magnitude of the force need to be applied at point B and the horizontal and vertical reactions at A to hold the beam in a horizontal position. (hint: What is the length of the spring now if the beam is in a horizontal position?) 3 ft A k = 100 lb/ft mmmmmmm 3 ft F B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam is shown in the figure given below where A is hinged, and B and C are roller supports. Use Three-Moment-Theorem to determine the end moments and draw the BMD for the beam. w kN/m P2 kN P1 kN B A D 2ΕΙ 2EI EI T77 L4 L3 L3 L2 Data Table L1 L2 L3 L4 P1 P2 (m) (m) (m) (m) (kN) (kN) (kN/m) 2 4 4 3 4 4 6.
Example 1: Find the maximum force (P) so that the total contraction is 0.25 mm. 50 x 50mm² Es = 210GPA 300тт Steel | 100 x 100mm? Eatu = 70GPA 380тm Aluminum
Given the following structure and assuming A is a fixed support, B a hinge, and C a roller, answer the following question: 12 ft B 12 ft IC 12 ft- D Question 1.4: Draw and upload the conjugate beam and represent all the forces with the adequate supports. O 20
N=25
0131% D 14:19 8.8 TNT Wi-Fi voWiFi •4* K/s a. Which of the following is the most stressed leg(s)? b. If the capacity of each leg is 25 kn, what is the safe value of W? c. Determine the axial force on leg AD if the maximum safe value of W is applied. SITUATION 4. Knowing that do = 3m, determine the following: 2m, 3m 3m de id 4m B DI 5kN 5kN 10KN a. Distance dɛ b. Reaction at E c. Total length of cable.
3. A steel beam is use to carry a uniform load of 25 kN/m over a span of 6 m. The left support must be at the end but the right support can be places at any reasonable distance from right end A. Which of the following gives the distance from the right support should be placed so that the smallest beam can be used? (hint: smallest beam used must have smallest maximum moment where +M -M... B. Compute for the maximum moment 25 kN/m
Calculate the stress in the steel of the section in PART B in MPa.0 and the ultimate moment capacity of the section in PART B in kN.m.0
4
Show freebody diagram. Show complete and detailed solution. A steel section with force T, force F, and force C is supporting waweight of 120kN. Given the coordinates of A, B, C, and D and assuming that E is in the origin. Find the following: 1. Force T 2. Force F 3. Force C
1.) Given the structure as shown below with height of 4m and 3 equal spans of 4m length. A. Determine the Force at member BG Express your answer up to 3 decimal places.
Consider the free body diagram for the truss system below. Taking moment about point A, determine reaction force R, B 80 kN A MATHalino.com MATHalino.com AH 1 m 1 m 1m 50 kN Ay Ro 0.75 m
Determine the vertical and horizontal reactions of the hinge support if the weight of M object is FN Kilonewton, value of a = SN and b = MN meters. The equivalent of 0 is 30 degrees Note: MN = 88 FN = 88 SN = 47 a Hinge b Cable m Beam com M Rope