Q1. [1 mark] I measure my bike tire pressure at noon, at 1 PM at 2 PM andat 3 PM. During the second hour it lost 80% of what it lost during the firsthour and during the third hour it lost 50 kPa. What was the tire pressureat noon?tP0A1Ar2Ar²3Ar3

Step 1: Write the equations for the lost pressure at each hour. The loss of tire pressure is just…

Answered: Q1. [1 mark] I measure my bike tire…

College Algebra

1st Edition

ISBN:9781938168383

Author:Jay Abramson

Publisher:Jay Abramson

Chapter3: Functions

Section3.3: Rates Of Change And Behavior Of Graphs

Problem 45SE: A driver of a car stopped at a gas station to fill up his gas tank. He looked at his watch, and the...

See similar textbooks

Similar questions

A driver of a car stopped at a gas station to fill up his gas tank. He looked at his watch, and the time read exactly 3:40 p.m. At this time, he started pumping gas into the tank. At exactly 3:44, the tank was full and he noticed that he had pumped 10.7 gallons. What is the average rate of flow of the gasoline into the gas tank?
At the start of a trip, the odometer on a car read 21,395. At the end of the trip, 13.5 hours later, the odometer read 22,125, Assume the scale on the odometer is in miles. What is the average speed the car traveled during this trip?
Find the intensity of light at a depth of 12 meter if I0=14 and k=0.7. Round to two decimals.
The kinetic energy E of an object varies jointly with the object’s mass m and the square of the object’s velocity v . An object with a mass of 50 kilograms traveling at 16 meters per second has a kinetic energy of 6400 joules. What is the kinetic energy of an object with a mass of 70 kilograms traveling at 20 meters per second?
A shaft is being cut in a lathe. The tool feeds (advances) 0.015 inch each time the shaft turns once (1 revolution). How many revolutions will the shaft turn when the tool advances 3.120 inches? Round the answer to 2 decimal places.
The carbon content of machine steel for gages usually ranges from 0.15% to 0.25%. Round the answers for a and b to 2 decimal places. a. What is the minimum weight of carbon in 250 kilograms of machine steel? b. What is the maximum weight of carbon in 250 kilograms of machine steel?
Cast iron 10 cm in diameter is turned in a lathe at 350 rpm. Each length of cut is 65 cm and eight cuts are required.A carbide tool is fed into the work at 0.0425 cm = 0.425 mm per revolution. Use the formula TLFN to find thetotal cutting time. Round the answerto 1 decimal place.
The resistance of a copper wire carrying an electrical current is directly proportional to its length and inversely proportional to its cross-sectional area. A copper wire with a diameter of 0.0126inch has a resistance of 64.9ohms per thousand feet. What length of 0.0201-inch-diameter copper wire will produce a resistance of 33.5ohms?
In 1906, San Francisco experienced an intense earthquake with a magnitude of 7.8 on the Richter scale. In 1989, the Loma Prieta earthquake also affected the San Francisco area, and measured 6.9 on the Richter scale. Compare the intensities of the two earthquakes.
In 2014, Chile experienced an intense earthquake with a magnitude of 8.2 on the Richter scale. In 2014, Los Angeles also experienced an earthquake which measured 5.1 on the Richter scale. Compare the intensities of the two earthquakes.
Compute the following problems. Express the answers to the nearer whole number. Use C=3.1416DN12 or DN12 for customary units and C=3.1416DN1000 or DN1000 for metric units. What is the surface speed of a 16-inch diameter surface grinder wheel running at1194 rpm?
A piece shown by the shaded portion is to be cut from a square plate 128 millimeters on a side. a. Compute the area of the piece to be cut. Round the answer to the nearest square millimeter. b. After cutting the piece, determine the percentage of the plate that will be wasted.

SEE MORE QUESTIONS

Recommended textbooks for you

College Algebra

Algebra

ISBN:

9781938168383

Author:

Jay Abramson

Publisher:

OpenStax

Algebra: Structure And Method, Book 1

Algebra

ISBN:

9780395977224

Author:

Richard G. Brown, Mary P. Dolciani, Robert H. Sorgenfrey, William L. Cole

Publisher:

McDougal Littell

College Algebra (MindTap Course List)

Algebra

ISBN:

9781305652231

Author:

R. David Gustafson, Jeff Hughes

Publisher:

Cengage Learning

College Algebra

Algebra

ISBN:

9781938168383

Author:

Jay Abramson

Publisher:

OpenStax

Algebra: Structure And Method, Book 1

Algebra

ISBN:

9780395977224

Author:

Richard G. Brown, Mary P. Dolciani, Robert H. Sorgenfrey, William L. Cole

Publisher:

McDougal Littell

College Algebra (MindTap Course List)

Algebra

ISBN:

9781305652231

Author:

R. David Gustafson, Jeff Hughes

Publisher:

Cengage Learning

College Algebra

Algebra

ISBN:

9781337282291

Author:

Ron Larson

Publisher:

Cengage Learning

Mathematics For Machine Technology

Advanced Math

ISBN:

9781337798310

Author:

Peterson, John.

Publisher:

Cengage Learning,

Trigonometry (MindTap Course List)

Trigonometry

ISBN:

9781337278461

Author:

Ron Larson

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Q1. [1 mark] I measure my bike tire pressure at noon, at 1 PM at 2 PM and at 3 PM. During the second hour it lost 80% of what it lost during the first hour and during the third hour it lost 50 kPa. What was the tire pressure at noon? t P 0 A 1 Ar 2 Ar² 3 Ar3