Q4) Which event will take place if there is a port security violation on switch S1interface Fa0/1, as given below? *si# show port-securitySecure Port MaxSecureAddr CurrentAddr SecurityViolation Security Action(Count)(Count)(Count)Fa0/1restrictO A. A notification is sentB. A syslog message will be loggedC. Packets with unknown source addresses won't be droppedD. The interface will go into error-disabled stateQ5) When multiple routing protocols have a route to the same destinationnetwork what determines which route is installed in the routing table? *a. Best metricb. Lowest hop countc. Greatest available bandwidthd. Lowest administrative distanceO e. Lowest cost Q1) Which task is performed by the dynamic routing protocols? *a. discover end devicesO b. update routing tablesO c. propagate host gatewaysO d. assign automatic IP addressingQ2) Which of the following is a static routing feature? *a. Security increases because only the network administrator may change the routingtables.O b. Configuration complexity decreases as network size increases.O c. Routing updates are automatically sent to neighbors.O d. Routing traffic load is increased when used in stub network links

1. task is performed by the dynamic routine protocol

Answered: Q1) Which task is performed by the…

Q1) Which task is performed by the dynamic routing protocols? * a. discover end devices b. update routing tables c. propagate host gateways d. assign automatic IP addressing

Comptia A+ Core 1 Exam: Guide To Computing Infrastructure (mindtap Course List)

10th Edition

ISBN:9780357108376

Author:Jean Andrews, Joy Dark, Jill West

Publisher:Jean Andrews, Joy Dark, Jill West

Chapter8: Network Infrastructure And Troubleshooting

Section: Chapter Questions

Problem 8TC

See similar textbooks

Similar questions

(2) If we obtain the following information from one router. What kind of routing protocol does it use? Provide its routing table, and the inferred local topology around it. Router#show ip route Codes: C connected, S static, R RIP, B BGP 0 OSPF, IA OSPF inter area - N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 OSPF external type 1, E2 OSPF external type 2 i IS-IS, su - IS-IS summary, L1 IS-IS level-1, L2 IS-IS level-2 - - ia - IS-IS inter area, * - candidate default Gateway of last resort is no set 192.168.1.0/24 is directly connected, FastEthernet 0/4 192.168.1.2/32 is local host. C C 192.168.2.0/24 is directly connected, FastEthernet 0/6 192.168.2.1/32 is local host. C R 192.168.10.0/24 [120/1] via 192.168.1.1, 00:12:52, FastEthernet 0/4 R 192.168.30.0/24 [120/1] via 192.168.2.2, 00:12:44, FastEthernet 0/6 CUCURR с
Which task is performed by the dynamic routing protocols? * a. discover end devices b. update routing tables c. propagate host gateways d. assign automatic IP addressing
IPV4 is a Connection oriented Protocol. * False True Broadcast is the process of sending a packet from one host to a selected group of hosts. * False True The prefix length is the number of bits in the address that gives the Host portion. " False True The metric is used to decide which route appears on the routing table. * True False The throughput value is greater than The Bandwidth Value. * True False O O O O
Give answer of all these questions in detail.
The Routing Information Protocol (RIP) is an intradomain routing based on routing. * link state distance vector path vector none of the above The metric used by is the hop count. * OSPF RIP BGP none of the above
In which situation a dynamic routing protocol is more beneficial than static routing? O a. on a stub network that has a single exit point b. in an organization where routers suffer from performance issues O c. on a network where there is a lot of topology changes d. in an organization with a smaller network that is not expected to grow in size
1. Static Routing Basics: What is static routing, and in what scenarios is it most appropriately used? Describe the steps to configure a primary static route on a router.
8 Scaling Networks
A routing protocol’s reliability and priority are rated by what measurement? a. Routing table b. MTU c. Latency d. AD
Which two statements about routing protocols are true (choose 2). a) OSPF elects designed routers on multi-access links. b) RIP does not support classless routing. c) EIGRP uses broadcast traffic to establish adjacencies with its neighbors. d) RIP does not advertise a route beyond a hop count of 15. e) IBGP is an internal routing protocol.
Which of the following consider disadvantages of static routing? a. Any change in the topology will affect the configuration. b. No need for extra resources such as CPU or bandwidth. c. The routing tables are small and maintenance is minimal. d. The route to the destination is always not change.
Why do protocols like HTTP, FTP, SMTP, and POP3 use TCP instead of UDP? When comparing Routing and Forwarding, what are the key distinctions? How does HOL blocking work? Where does it happen, the input or the output?