Q1/ What is the acceleration due to gravity in a region where a simple pendulum having a length 75 cm has a period of 1.7357 s? Q2/ A pendulum on the Earth has a period T. The acceleration due to gravity on Mars is less than that on the Earth, and the acceleration due to gravity on the Moon is even less than on Mars. Identical pendulums have the same mass and length. Where would the period of an identical pendulum be the smallest? a. The period is smallest on the Earth. b. The period is the same on the Earth, the Moon, and Mars. c. The period is smallest on Mars. d. The period is smallest on the Moon. e. The period is smallest on both Mars and the Moon. Q3/ How would the period of a simple pendulum be affected if it were located on the moon instead of the earth?

Q1/ What is the acceleration due to gravity in a region where a simple pendulum having a length 75 cm has a period of 1.7357 s? Q2/ A pendulum on the Earth has a period T. The acceleration due to gravity on Mars is less than that on the Earth, and the acceleration due to gravity on the Moon is even less than on Mars. Identical pendulums have the same mass and length. Where would the period of an identical pendulum be the smallest? a. The period is smallest on the Earth. b. The period is the same on the Earth, the Moon, and Mars. c. The period is smallest on Mars. d. The period is smallest on the Moon. e. The period is smallest on both Mars and the Moon. Q3/ How would the period of a simple pendulum be affected if it were located on the moon instead of the earth?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1. Draw and explain five casting defects in sand casting process. briefly.
QUESTION 18 Rearrange the following steps which illustrate the sand-casting process in brief. Heat treatment of casting product is sometimes required to improve metallurgical properties Pour the molten metal into sand mold Cavity Break up the mold to remove casting A Allow time for metal to solidify + Clean and inspect casting product Make the Pattern and Core box * Separate gating and riser system + Prepare sand casting mold for pouring QUESTION 19 Which of the following is mostly used for holding bored part of the job? Mandrels Steadies Collet Face plate
What manufacturing processes do you think were applied? Or what information be needed about the fabrication of this piece?
Determine relationship: relative permittivity – capacitance ; (direct, inverse, no effect) molecular weight – glass transition temp ; (direct, inverse, no effect) alumina Frenkel defects – electronic heat conduction ; (direct, inverse, no effect) alumina porosity – thermal insulation ; (direct, inverse, no effect) magnetization – relative magnetic permeability ; (direct, inverse, no effect)
نقطة واحدة The third sequence in the Injection machine of polymers, a shot of melt, which has been brought to the right temperature and viscosity by heating and the mechanical working of the screw, is injected under high pressure into the mold .cavity TO FO * Coppola is used to convert pig iron to gray .cast iron TO F LL
Bainite is an intermediate of pearlite and martensite in terms of hardness.
I want a step by step working out on how all these values were obtained and what table was used
Consider the casting in (Figure 1). Figure 20 mm 40 mm 120 mm 40 mm 1 of 1 Part A Determine the distance to the center of mass of the casting that is formed from a hollow cylinder having a density of 3.2 Mg/m³ and a hemisphere having a density of 3 Mg/m³. Express your answer to three significant figures and include the appropriate units. IN = μᾶ Value Submit Previous Answers Request Answer X Incorrect; Try Again Units < Return to Assignment Provide Feedback ?
2 - What is the appropriate device for diagnosing each of the following and why? A- The aluminum plate is coated with a nano-solution. b- A colloidal sample containing nano-solutions. C- Study of the microstructure of the surface of a sample of iron. D- Study the phases and components of the organic powder.
When forming a solid object in SolidWorks, there are a number of key words and phases. select ONLY the ones related to SoildWorks. construction line inheritance D wiggle substitution relations save bend implode pointers reference point In Plane extrude sketch
What is normalizing?
Baking of sand mold increases its strength. Select one: True False