Q1: What are the components of air handling unit? And list the main difference between the air handling unit AHU and the fan coil unit FC.

Q: DRAW A Double acting cylinder circuit for pneumatic system using 5/3 lever operated DCV

A: In this problem, it is asking about drawing a double-acting acting cylinder circuit for pneumatica…

Q: Make a circuit for representing starting system of vehicle.

A: The starting system is one of the engine's systems, which provides an engine start. To make it, the…

Q: The oil level sensor use the ... technic for * operation.

A: Oil level sensors: A oil level sensor works on the principle of buoyancy.

Q: While discussing EGR systems with a differentialpressure feedback electronic (DPFE) sensor:…

A: Exhaust Gas Recirculation (EGR) is a cost-effective and efficient method for lowering nitrogen…

Q: 1. How Does An Air Handling Unit Work?

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: what is the functional difference between an accumulator and an ABS fluid accumulator

A:

Q: List all the control modes for both engine crank and engine warmup.

A:

Q: I need parts 5 and 6 answered pertaining to the print and set of sequence of operations.   Note: If…

A: When the operator actuate the two-push button valves (1) and (2) until the weight starts to descend.…

Q: Based on the circuit shown in Figure 19-11, complete the following exercises: A. Complete the chart…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: b) What would happen if the ABS system having a fault? Explain why this could happen.

A: Given ABS To find Consequence of ABS faults Reason for ABS faults

Q: draw a Single acting cylinder circuit for Hydraulic system using 3/2 single solenoid valve operated…

A:

Q: Technician A says that the oxygen sensor provides the major input during the open-loop mode.…

A: Explanation:     The closed-loop and open-loop refer to the mode of operation of engines that are…

Q: your y1 and y2 are still in deg mode?

A: Explanation: In the given solution, y1 and y2 are in deg mode. It should be in radian mode.

Q: While discussing ignition timing control in EI systems: Technician A says that when the engine…

A: The ignition timing control in the electronic ignition system, the coolant's temperature must be…

Q: Explain with a neat sketch of Electronic Ignition System.

A: Electronic mechanism is that the style of mechanism that uses electronic circuit, usually by…

Q: While discussing EFI systems: Technician A says that the PCM provides the proper air-fuel ratio by…

A: The PCM chooses the air-fuel proportion by admiring the look-into tables enlisted in its memory. The…

Q: what allows the stator to operate correctly during vortex and rotary flow 1. the torque converter…

A: The torque converter clutch allows the stator to operate correctly during vortex and rotary flow.

Q: Automatic transmissions use a __ instead of a clutchto transfer power from the flywheel to the…

A: An automated car is one that has an automatic gearbox and does not require the driver to manually…

Q: .Explain how to use the device to start the engine (0 to idle speed) with the vehicle not moving

A:

Q: OBD II systems use several modes of operation. List three of them.

A: There are nine Global OBDII modes. Three of them are Monitor Status and Current Data, Freeze Frame,…

Q: Technician A says that the oxygen sensor provides the major input during the open-loop…

A: There are two modes of operations for the engine: (1) Open loop mode: In this mode, no feedback is…

Q: List five advantages the use of piezoelectric injectorshas over solenoid-based injectors.

A: Given Injectors To find Advantages of piezoelectric injectors over solenoid-based injectors

Q: 2. How many types of air handling units are there? explain 3. What are the components of an air…

A: Air Handling Unit

Q: Explain Air Cooling System for I.C. Engine in detail

A: Solution:: In the air-cooled system, a current of air is made to flow past the outside of the…

Q: Draw a simple schematic of a 3-way, 2 position air piloted directional control valve operating a…

A: 3 way means no. of ports are 3. 2 position means no. of positions of the switch. The required…

Q: The causes of suspended load in the traction system are: a. Laminar current b. turbulent current c.…

A: The cause of suspended load in the traction system are turbulent current.

Q: In cruise you have the FSTN BELTS in the OFF position...What would cause the NO SMKG and FSTN BELTS…

A: In an aircraft, the NO SMOKING and FASTEN SEAT BELTS signs are typically controlled by the flight…

Q: timing diagram with IPO, IPC, TPO, TPC,EPO, EPC as 35,35,40,40,35,50

A: The port timing diagram for required functions with angle is shown below.

Q: Identify the sensor which uses float for its operation.

A: Identify the sensor which uses float for its operation. Answer: Rotameter

Q: What is the name for the gas-filled pressure chamberthat is part of the antilock braking system’s…

A: The antilock braking system is a safty anti skid braking system that is normally used in modern…

Q: When the throttle plates are closed in a port injectionsystem, where does the air needed for idle…

A: Port fuel injection on which fuel is delivered directly into the cylinder head or intake manifold of…

Q: In a typical all wheel drive automatic transaxle, what controls the transfer clutch?a. Transmission…

A: In a typical all-wheel-drive automatic transaxle, the transfer clutch isn't directly controlled by a…

Q: What is difference between AHU and FCU?

A: given:what is difference between AHU and FCU

Q: VOR can be tuned from the following places in most large body aircraft. Nav control panel MCDU…

A: To find: The VOR can be tuned from the following places in most large body aircraft. Explanation: A…

Q: Discuss the effect of malfunctioning cooling system on IC engines.

A: Solution:

Q: The EWB system relies on the vehicle's battery for power but what if the vehicle battery fails ?

A:

DDCS

With the involvement of computers in almost every aspect, large-scale manufacturing industries have already made a major shift from manual working towards a fully automated manufacturing process. This shift has replaced the man with machines. Automating manufacturing processes reduces dependency on human labor to a greater extent as result unnecessary labor charges are removed. Automation also leads to superior product finishes with extreme accuracy. The material processing time is reduced with reduced output delay. An interconnection between machines and electronic systems automates a manufacturing process. A variety of sensors pick the inputs and feed them into a device, which is a microcontroller-based computer system. This system indeed operates the machinery. An example of such a system is the DDCS, which stands for direct digital control systems. DDCS means an automated control of a condition or a process by the use of a variety of digital devices, mostly computer systems or workstations.