Q1: Three principal stresses are applied to a solid where o, = 400 MPa, 0₂ = 200 MPa, and os = 0. (a) What is the ratio de/des? (b) If a fluid pressure produces an all-around hydrostatic stress =250 MPa that is superimposed upon the original stress state, how does the ratio in (a) change? Explain the result.

Q1: Three principal stresses are applied to a solid where o, = 400 MPa, 0₂ = 200 MPa, and os = 0. (a) What is the ratio de/des? (b) If a fluid pressure produces an all-around hydrostatic stress =250 MPa that is superimposed upon the original stress state, how does the ratio in (a) change? Explain the result.

Name: Q1: Three principal stresses are applied to a solid where o, = 400 MP
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Q1: Three principal stresses are applied to a solid where o, = 400 MPa, 0₂ =200 MPa, and os = 0.(a) What is the ratio de/deg?(b) If a fluid pressure produces an all-around hydrostatic stress =250 MPathat is superimposed upon the original stress stat

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. At a point in a brocket, the stresses on two mutually perpendicular planes are 180 MN/m? (tensile) and 70 MN/m2 (Compressive). The shear stress across the planes is 65 MN/m2. Find the following by Mohr's Circle method and compare with Analytical solutions: (i)The Normal stress on a plane making an angle of 50° with the plane of first stress. (ii)Shear stress on the plane (iii) Maximum shear stress (iv) Resultant stress and it's direction. (v) Major and minor principal stresses.
For the following data, using Mohr's circle of stress and trigonometry, (a) Find the principle stresses and show their sense in properly oriented element and (b) find the maximum (principle) shear stresses with the associated normal stresses and show the results on a properly oriented element.
Question 4 At a point in a thin steel plate in plane stress (oz = Txz = Tyz = 0), Ex=800H, Ey= - 400, and Ky = 200. For the steel plate, G = 76.92 GPa and V= 0.30. (a) Determine the extensional strain &zat this point. (b) Determine the stresses Ox, Oy and Txy at this point. (c) Determine the change in volume or dilatation, &v, at this point.
- Lo- do
Consider the following plane stress state: Ox=30 MPa, y= -60 MPa, Txy= 30 MPa cw Calculate the following: 1. The coordinates of the center of the Mohr's circle C The location of the center of the Mohr's circle Cis ( 2. Principal normal stresses (01, 02) The principal normal stresses are σ₁ = 39.08 3. Maximum shear stress (7) The maximum shear stress is 54.08 MPa. 4. The angle from the x axis to 0₁ (p) The angle from the x axis to 0₁ (p) is -16.85 5. The angle from the x axis to 7 (s) The angle from the x axis to T (s) is 28.15 6. The radius of the Mohr's circle The radius of the Mohr's circle is 54.08. ✰ MPa. MPa and 02 = -69.08 MPa. O -15 MPa, CW CCW O MPa).
2. The discs in the spinal column can withstand a stress (force per unit area) of 1.1 x 107 N/m2 before they rupture. (a) If the cross-sectional area of your discs is 10 cm2, what is the maximum force that can be applied before rupture takes place? (b) Estimate the stress at a disc located at the level of the center of gravity of your body when you are standing vertically. (c) What types of situations might the body experience where the stress on this vertebra would be much larger than in (b) above?
M13.6 Principal stresses from rosette data scenes -200 µE 23 Eb = 200 με Ec 500 µE 30° 30° Ex (LE) a Ey (µE) Yxy (Lurad) The strain rosette shown was used to obtain normal strain data at a point on the free surface of a steel (E = 200 GPa; v = 0.32) plate. Op1 (MPa) Determine the normal strains, the shear strain, and the principal stresses in the x-y plane. Op2 (MPa) Try One 1st 2nd 3rd attempt enter
Problem 2 The experimental set-up depicted in fig. 2 is aimed at studying the behavior of materials under complex stress states. A thin-walled pressure vessel of radius R = 11 mm and thickness t = 2.0 mm is subjected to an inter- nal pressure pi. At the same time, a normal force, N, and a torque, Q, are applied to the sample. In a specific experiment, the applied normal force is N = 16 kN and Figure 2: Pressure vessel subjected to the internal pressure p; = 20 MPa. The applied torque internal pressure, external torque and is slowly increased. The first permanent deformations are axial force. observed at the outer surface of the sample when Q = 120 N-m. (1) Find the yield stress for the material if it is assumed to follow von Mises' yield criterion. (2) Find the yield stress for the material if it is assumed to follow Tresca's yield criterion. (3) 2R P. Based on von Mises' yield criterion, find and plot the yield surface in the space defined by the three loading components, the internal…
Answer the questions below for the following system. Young's modulus and Poison's ratio can be taken as 200 GPa and 0.3, respectively. a) Calculate and determine the stress state for point H using undergraduate level solid mechanics knowledge? b) Determine the principal stress values at point H using undergraduate level solid mechanics knowledge Top view of section where H is located O Point H 300 mm 120 mm 540 mm .H Diameter of the pipe d=36 mm P=900 N
Determine: a. The change in length of rod EF b. The stress in each rod.
In the attached picture there is a sketch of a socket wrench. Assume the wrench is held at a fixed point “A”. The yield stress of the material is known to be 500 MPa. Answer the questions below Describe the stresses at point “A” and their causes and calculate the stresses. Determine the factor of safety against yield assuming the Tresca yield criteria. Determine the factor of safety against yield assuming the von Mises yield criteria using both principal stresses and “Cartesian” stresses. Do your values match or not, and is this expected? Explain. Do the calculated values make sense with the respect to the Tresca value? Explain, why or why not?
Daboost/Shutterstock.com 7.2-8 An element in plane stress on the fuselage of an airplane (figure part a) is subjected to compressive stresses with a magnitude of 42 MPa in the horizon- tal direction and tensile stresses with a magnitude of 9.5 MPa in the vertical direction (see figure part b). Also, shear stresses with a magnitude of 15.5 MPa act in the directions shown. Determine the stresses acting on an element ori- ented at a clockwise angle of 40° from the horizontal. Show these stresses on a sketch of an element ori- ented at this angle. (a) PROBLEM 7.2-8 T 9.5 MPa Ţ 42 MPa 15.5 MPa 7.2-21 An element in plane stress from the frame of a racing car is oriented at a known angle (see fig- ure). On this inclined element, the normal and shear stresses have the magnitudes and directions shown in the figure. Determine the normal and shear stresses acting on an element whose sides are parallel to the xy axes, that is, determine ox, o, and 7. Show the results on a sketch of an element…