Q1: The E-MOSFET of Figure was analyzed with the result that: k = 0.24 x 10 A/V, VGso = 6.4 V, Ipo = 2.75 mA. (a) Determine gm- %3D %3D (b) Find ra. (c) Calculate Z; with and without ra. compare results. (d) Find Z, with and without ra. compare results. (e) Find A, with and without ra. compare results. 9 12 V 2 kN 1 µF Z. 10 MQ ID(on) = 6 mA Vas(on) =8 V VGS(Th) = 3 V Yos = 20 uS V, o- 1 uF %3!

Q1: The E-MOSFET of Figure was analyzed with the result that: k = 0.24 x 10 A/V, VGso = 6.4 V, Ipo = 2.75 mA. (a) Determine gm- %3D %3D (b) Find ra. (c) Calculate Z; with and without ra. compare results. (d) Find Z, with and without ra. compare results. (e) Find A, with and without ra. compare results. 9 12 V 2 kN 1 µF Z. 10 MQ ID(on) = 6 mA Vas(on) =8 V VGS(Th) = 3 V Yos = 20 uS V, o- 1 uF %3!

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

6. For a particular dual-slope ADC: Vref = +5.0V and the charge time is 6ms. %3D a) " Draw a time-domain plot for the dual-slope ADC. b) When Vin = -2.5V, what is the total conversion time? c) When Vin increases by 1.0V, what is the total conversion time?
VoO for Ma mosfet Nn Cox ( )= Jm Alv? ,Vrw=0,7V J00NA (+) VX %3D %3D a) In uhat condition does the mosfet work ?and frnd the voltage Vx= ? M1 3V b) what is the mompmum Voo voltage and why'?
a) Draw the energy band diagram of a MOSFET transistor, when -5 volts are applied to the drain contact. b) Explain what will happen to the Fermi level at the source contact and the drain contact in the following scenarios (Use an appropriate energy diagram to illustrate your answer): A positive voltage is applied to the drain contact. A positive voltage is applied to the source contact. c) Explain why current flow in a MOSFET transistor. Use a diagram to illustrate your answer.
a. Illustrate any differences or similarities between BJT and FET. b. Draw the V-I characteristic of an ideal diode Model. c. Draw the circuit symbol of a common emitter configuration of an NPN transistor.
Choose whether the followings are True or False. 1. The MOSFET has 2 terminals Drain and Source. 2. An E-MOSFET operates in the depletion mode. 3. The LED emits light when reverse biased. 4. In the n-channel E-MOSFET, VGs(th) has a positive value. 5. A diode conducts current when forward biased and blocks current when reverse biased 6. An n-channel D-MOSFET with a positive Vcs is operating in the enhancement mode. 7. The varactor diode acts as a variable capacitor under forward bias conditions. 8. Once a BJT transistor is in the saturation, a further increase in base current will cause the collector current to increase. 9. In a given BJT transistor amplifier, Rc=2.2KQ and r'=20 Q then the voltage gain is equal to 110. 10. Voltage Amplification Av in a BJT is the output voltage divided by the input current
b. [PI-3.a] Define electrochemical potential "p" and give the condition under which electrochemical potential p₁ at source junction of a MOSFET channel is equal to the electrochemical potential µ₂.
Kindly provide a CLEAR and COMPLETE solution.
In a Bread Board, the rows are shorted or the columns are shorted? The BJT is operated in The Zener diode may have a breakdown voltage from about mode. Transistor has doped regions. Which one is the full form of DMM? In forward region Zener diode Clipper Circuits When the diode is connected across a voltage source with positive polarity of source connected to P side of diode and negative polarity to N side, then the diode is in A rectifier converts an In Full-wave bridge rectifier how many diodes are needed? condition. signal into a signal.
Show the downward shift of the output signal with the series capacitor and diode.Clampers or DC restorers are clamp a peak of a waveform to a specific DC level comparedwith a capacitively coupled signal which swings about its average DC level (usually 0V).If the diode is removed from the clamper, it defaults to a simple coupling capacitor– noWhat is the clamp voltage? And, which peak gets clamped? Why is this so? Voltage values: Capasitor value: 1000 pFDC offset: 0 VAmplitude: 5 VFreq: 1 KHz
Q.7 Light-emitting diode (LED) is simply a diode that is designed to emit light. Voltage drop for LED is 0.8V. What happens to the LED when it is connected to the voltage source as in Figure A1? Why? (Describe in terms of majority carrier movement). LED 5V 1kQ Figure Al
QUESTION 3 a. Design such a power supply with an input Voltage ranging from 10V to 15 V, and a limiting Resistor of 4.0 kn. Specifications of the Zener diodes are; Var is 8 V and Rz is 1000. Your task is to obtain regulated output Voltage within the input voltage range. b. With a diagram describe the operation of a clipper that can clip at two independent levels. c. In the circuit below, the values of Rc = 4.7 kN, RE = 3.3 kN, Vs = 4 V and also Vcc = 10 V and B = 100. Prove that the BJT is operating in the active mode. +10 V Re- 4.7 k +4 V R-3.3 kn
Draw the energy band diagram of a p-n-p* bipolar junction transistor. Show all the relevant energies - conduction and valence band edges, Fermi energies, Intrinsic Fermi energy and built-in potentials. Identify which region is heavily doped. Draw very carefully and in a very tidy manner. No free hand diagrams