Q1: System Timing A program consists of 5,000 floating-point instructions and 25,000 integer instructions. Processor A has a clock rate 2.0 GHz. Floating point instructions take 7 cycles and integer instructions take 1 cycle. How long does it take this processor to run the program?               Processor A runs program2 consisting of 100,000 floating-point instructions and 50,000 integer instructions. What is the average CPI for this program?     Processor B has an average CPI for program2 of 3.5, its clock rate is 1.8 GHZ. How much time does it take to execute the program?       Which processor is faster and how much?     Processor _____________ is ___________ times faster the Processor __________

Q: 1.3.A program with 1.5 x10 instructions is running on a 3 GHz processor with a CPI of 0.5 а.…

A: GIVEN: Instruction Count= 1.5×103 instructions CPI = 0.5 Clock rate = 3GHZ = 3×109 cycles/sec…

Q: Stella designs a 3 GHz processor where two important programs, A and B, take one second each to…

A: Your answer is given below with a detail solution.

Q: Assume that a program has 9277 instructions, and a CPI of 2.3. What is the number of clock cycles of…

A: Given instructions=9277 CPI =2.3 Find  -.  clock cycles needed CPI means clock per…

Q: Computers Problem 3. Suppose you wish to run a program P with 7.5 billion instructions on a 5GHZ…

A: The Answer is in Below Steps

Q: A program consists of 100,000 instructions as follows: Instruction Type Integer arithmetic Data…

A: We don't need to calculate the CPI for this given problem.   Speed Up of machine M with two CPU can…

Q: Assume for a given program, 60% of the executed instructions are of Class A, 10% are of Class B, and…

A: Class A Instructions =  60% = 0.6 Class B Instructions =  10% = 0.1 Class C Instructions =  30% =…

Q: Given the processor circuit below, what are the bits of the following items if the instruction add…

A: To understand the bits involved in the execution of the instruction `add $t2, $t3, $t4`, let's break…

Q: A program runs in 15 seconds on computer X, which has a 4 Ghz clock. You are required to help a…

A: INTRODUCTION: Here we need to tell the what clock rate should you tell the designer to target.

Q: Consider a system with only two types of instructions, A and B. Type A instructions each require 7…

A: Given: Type A instructions each require (CPIA ) = 7 clock cycles Type B instructions each require…

Q: Assume that a program requires the execution of 125x106 FP (floating point) instructions, 130x106…

A: Assume that a program requires the execution of 125x106 FP (floating point) instructions, 130x106…

Q: If it is executed on a 43 MHz processor with the following Instruction Class CPIs, what is the…

A: Compiler: It is a special program which translates a programming language's source code into…

Q: to complete the table below: Instruction MVI A.A5 ML 2000 СМА XRI FF ORI 5A LXI H, 2020 MOV M,A INR…

A: It is defined as microprocessor system consists of data input, storage, processing and output…

Q: In C++   Write a code snippet to automatically increase the size of the dynamic array…

A: Given requirement, Write a code snippet to automatically increase the size of the dynamic array…

Q: Q2. P1, P2, and P3 are three processors executing the same instruction set. P1 has a 3 GHz clock…

A: To determine which processor has the highest performance expressed in instructions per second, we…

Q: two different processors execute same instructions, Processor one has 4Ghz clock rate and 1.5 CPI,…

A: Performance of Processor = clock rate * CPI. Number of cycles = execution time*clock rate Number of…

Q: A compiler produces a program with the following mix of instructions: Instruction Class Count 6 9 9…

A: We are given instructions count, CPI (Cycle per Instruction) and clock period. And we are asked to…

Q: pe 1 instructions require 1 cycle to finish. pe 2 instructions require 4 cycles to finish. pe 3…

A: Introduction: The CPU executes instructions of different types that require varying amounts of time…

Computer Fundamentals

The computer is termed computation. For calculating or computing something the device that has been used is known as the computer. Or we can say that for performing a fast arithmetic operation the device that has been used is a computer. Storing, processing, and retrieving are the main features of a computer.