Q1: ph paper when required. A-The analog signal s(t) = 10 cos (20 pi't) cos (200 pi*t) is sampled at the rate of 250 samples per seconds. Determine the following: a- The maximum frequency component present in the analog signal. b-Nyquist rate. B- An analog signal having single frequency as 3 kHz is sampled with 5 kHz signal. Describe its frequency spectrum. What will be the output if the sampled signals are passed through a low-pass filter having cutoff frequency at 2.5 kHz?

Q1: ph paper when required. A-The analog signal s(t) = 10 cos (20 pi't) cos (200 pi*t) is sampled at the rate of 250 samples per seconds. Determine the following: a- The maximum frequency component present in the analog signal. b-Nyquist rate. B- An analog signal having single frequency as 3 kHz is sampled with 5 kHz signal. Describe its frequency spectrum. What will be the output if the sampled signals are passed through a low-pass filter having cutoff frequency at 2.5 kHz?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Describe the signal in Figure E.49 as a ramp function minus a summation of step functions. 15 x(t) Imm 4
I need the answer quickly
An analog signal of maximum frequency 5KHz is sampled at a certain sampling frequency. The reconstructed analog signal from the samples was distorted. Then which of the following was the sampling frquency? a. 12 KHz b. 10 KHz c. 5KHz d. None of these options
Powered by ±10VIntegrator circuit designed with Op-AmpVin=3sin(2π400t) alternative signal to inputhas been applied. Analysis of output voltage (Vo)Draw the waveform.Calculate the maximum and rms value of out signal.
2. Plot the transfer function, and clearly indicate the on/off conditions of each diode, the slope of the line, and the voltages of turning points in each operating region for the following circuits. Assuming the constant-voltage model (VD,on = 0.8 V) is used to determine the DC level. Also, Plot the output waveform in time-domain if the input signal is as shown below with the amplitude and other important values labeled in the figure. (a) (b) Vin R= 500 D₁ V₁= 2.5 V D₂ A V₂ 1.6 V D₁ 2R 2X4 2R D₂ 3R out Vout Vin Vin 10 mv 1-AAAA-3.4 V >t 5 V
A signal x()-5sin(1000nt)+ 5sin(1500tt) is sampled with sampling speed f: and the sampled signal is shown in the figure below. Is the signal sampled correctly. Prove your answer. 10 St(sec) 4. -8 -10 Volts
Electronic
what to answer in, "have have you learned in Fundamentals in Mixed Signals and Sensors". thank you.
A signal has a frequency of 20 Hz and duty cycle of 25%. For this signal, fill in the following Signal Period in mSec Signal off time in mSec Signal on time in mSec
7-22 Abasehand signal with frequency components from near de to 15 kHz frequency modulates a 200-kHz carrier, and the frequency deviation is +3 kHz. The signal is applied as the input to a cascade of two frequency triplers and one frequency doubler. Determine the output (a) center fre- quency, (b) frequency deviation, and (c) deviation ratio.
Assuming that output Q=0 initially (before point A), apply the waveforms x and y shown in the figure to inputs S and R, respectively, of an SR NOR Latch.Question: What is the value of output Q' at point G?a. lowb. highc. indeterminated. transitioning from low to highe. transitioning from high to low
Ce301 q4c