Q1: Find the discharge through the pipeline in the Fig. for H= 10 m, as shown. Use minor loss coefficients for the entrance, elbows, and globe valve of 0.5, 0.9 (each), and 10, respectively. 1 150-mm-diam clean cast iron pipe H = 10 m + Water 20 °C 12 m Globe valve Standard elbows 30 m 60 m Square-edged entrance f for pipes=0.023

Q1: Find the discharge through the pipeline in the Fig. for H= 10 m, as shown. Use minor loss coefficients for the entrance, elbows, and globe valve of 0.5, 0.9 (each), and 10, respectively. 1 150-mm-diam clean cast iron pipe H = 10 m + Water 20 °C 12 m Globe valve Standard elbows 30 m 60 m Square-edged entrance f for pipes=0.023

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

At night, water is pumped from a treatment plant reservoir through distributing piping to an elevated storage tank. Assume no other withdrawals from the system. The water surface in the supply reservoir is at 3m elevation, the lift pump elevation is 6m, the water elevation in the elevated tank is 42m. The pipe network maybe considered equivalent to 1500m of 250mm diameter. Use C=100. There is a supply of 60 Liters/sec. to the tank. a. Compute the head loss of the 250mm diameter pipe. b. Compute the pump discharge pressure required to supply a flow of 60L/s to the tank, c. Compute the slope of the energy gradient
Water flows steadily downward through the pipe shown in the figure below. Viscous effects are negligible, and the pressure gage indicates the pressure is zero at point (1). Determine (a) the flowrate and (b) the pressure at point (2). (a) Q = (b) p2 = 2.1ft 3.1ft ↓s -0.12 ft (1) 5 -0.1 ft -free jet ft³/s lb/ft²
pipe 310 m Water is flowing in a straight concrete lining centrifugally spun pipe as shown in the figure problem 12. The difference between the two gauge readings is 185 kPa. The flow rate is designed to be 30 liter/s. By using Darcy Weisbach and Hazen William's formula, determine the pipe diameter. (Ans.: 228 mm, 123 mm) TABLE 5.1: Pipe Characteristies Pipe Hazen-William* Roughness e (mm) 0.15 C 140 Asbestos Cement (AC) – all ages Cast Iron, Ductile Iron - new 0.3 130 10 years old - 20 years old 1.5 3.0 100 90 Cast Iron coated – good condition all ages Welded steel - uncoated - new 0.3 135 125 100 100 - old 0.6 1.5 Coal tar enamel coated steel – new Concrete lining centrifugal spun – all ages Galvanized Iron (GI), Mild Steel (MS) HDPE, UPVC, Polyethylene Wrought Iron Copper, Brass *The Malaysian Water Association - MWA (Design Guidelines for Water Supply Systems) 0.15 0.15 140 0.3 130 0.015 155 0.045 ND 0.0015 ND ND = No Data
Q2. Determine the flow rates in the three Cast Iron pipes in the figure shown (Assume complete turbulence, rough pipes). P1 Tank 1 Pipe 1 45 m P3 P2 Tank 3 Tank 2 Pipe 3 Pipe 2 D e ipe L (m) e/D f k Pipe Equation (cm) (тm) (m³/s) 1 15 180 20 100 3 12 55 Pressure (P) (pascal) Tank z (m) Total Head (m) 1 50,000 2 300,000 3 70,000
The total head loss from A to E is 12 meters. Determine the following: discharge in pipe no. 1. = _________ m3/s head loss in pipe no. 3. = _________ meter discharge in pipe no. 2. = _________ m3/s
3. [Ch4 - 1] What is the head loss and corresponding pressure drop (in units of bars) across a 30- mm-wide open gate valve when oil (SG = 0.90) flows through at a rate of 4 x 10-3 m/s? 4. [Ch4 – 2] Oil (SG = 0.80, v = 10- m/s) flows at a rate of 2 x 10-3 m'/s through a 20-mm- diameter commercial steel pipe. What is the equivalent length of a 20-mm-half open gate valve placed in the line?
A commercial steel pipe—with a diameter, D, of 200 mm and length, L, of 30 m—is used to drain oil (S.G.=0.8)tank. Determine the discharge, in liters per second, when the oil level in the tank is 3 m above the exit of the pipe.Neglect component or minor losses and quantify the friction losses using the Darcy-Weisbach equation shownbelow, use friction factor, f, of 0.12.
A pipe connected in series has the following roughness or friction coefficients: Pipe 1 C = 80 (Hazen-Williams) Pipe 2 n = 0.015 (Chezy-Manning) Pipe 3 f = 0.025 (Darcy-Weisbach) All pipes have a diameter of 400mm, length of 1 kilometer, and flow rate of 150 L/s. Determine the headloss on Pipe 1 in meters.
The figure below shows a fabricated assembly made from three different sizes of standard steel tubing listed in Appendix G.2. The larger tube on the left carries 0.075 m3/s of water. The tee branches into two smaller sections as shown. Reducing tee Flow 100-mm OD x 3.5-mm wall steel tube - 160-mm OD x 5.5-mm wall steel tube - 50-mm OD x 1.5-mm wall steel tube Required If the velocity in the 50-mm tube is 10.00 m/s, what is the velocity in the 100-mm tube to the nearest 1000th?
Oil flows at 62 L/s in a pipe of 175mm diameter and 50m length. SG of oil is 0.9 and viscosity is 0.04 Pa-sec. If head loss is 5.22m, determine: a) Mean velocity of flow = [ Select ] m/s b) Type of flow = [ Select ] %3D c) Friction factor = [ Select ] d) Velocity at the centerline of pipe = [ Select ] v m/s e) The shear stress at the wall of the pipe [ Select ] Ра %3D
- Probl Water flows from a large open tank, through a valve and out a pipe to atmosphere. A-9 cm². Az = 11m. h₁ = 5V²/2g Find: I Discharge (Q=?) in pipe. Assumptions: a = 1.