Q1) Draw the shear and moment diagrams for the shaft. The supports at A and at B are journal bearings.A = lw = 100 16/6+ (4f+) = 400 lb200 lb100 lb/ftB300 lb-ft1 ft4 ft+10+

Answered: Q1) Draw the shear and moment diagrams…

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. Take: d1 = 1 m, d2 =1 m, d3 = 1 m, d4 = 1.2 m, d5 = 1.4 m, F1 = 691 N/m, and F2 = 1,189 N. Determine the bending moment (Mc) acting on the cross section at C in N-m. Hint: consider the sign convention for internal loods. F1 В + di d2 d3 d4 ds F2
Smooth journal bearings at A and B that only exert vertical reactions on the shaft as shown below support the shaft. Based on the loading and support conditions shown, address the following: (a) Sketch the shear and moment diagrams using the graphical method - label all significant conditions. (b) If d = 90 mm, determine the absolute maximum bending stress in the beam, and sketch the stress distribution acting over the cross section. A 3 m 12 kN/m B 1.5 m
The tongs are used to grip the ends of the drilling pipe with the center at C. a) At what angle 8 would the torque (moment) reach a maximum about C? b) What is the value of that 100.0 lbs maximum torque or moment (using the angle in (a) above- about C? c) If the slope of the force was set to a 4/3 slope (i.c., y-4 and x=3) what would the torque or moment be about point C? d) Check your answer in (c) above by calculating the moment of this force about C by using a Vector formulation with the position vector CD. Show the moment vector as a Cartesian Moment Vector with its direction cosine angles. (Show the matrix for manual calculations and then either calculate it manually or use a calculator to calculate it.) 8.0 in 24.0 in
Determine the torsional shear stress in the shaft section AB and BC. There is a fixed support at C that can resist a moment. (Image taken from Statics and Mechanics of Materials by Beer, Johnson, DeWolf and Mazurek) T₁ = 300 N-m 30 mm TB = 400 N-m 46 mm 055 Shear Stress in AB = Shear Stress in BC= B 0.9 m 0.75 m units: units:
Problem Statement Based on Problem 7-60 from the textbook. The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. Draw the shear and moment diagrams for the shaft. w=285 lbs/ft a=5.4ft
Problem Statement Based on Problem 7-60 from the textbook. The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. Draw the shear and moment diagrams for the shaft. w = 295 lbs/# a= 5.5 ft A a W a
Determine the bending moment at point C if P1 = 215 |b/ft, P2 = 417 lb/ft, and P3 = 210 lb/ft. P2 வியூப்பன்பு A IC P1 - 4 ft- - 4 ft- - 4 ft- P3 - B - 4 ft- E
The shelf bracket is subjected to the force F = 336 Newtons at an angle 0 = 25.5°. Compute the moment (in N-m) that this force exerts about each of the two attachment points (screw locations in the figure). Take counterclockwise moments to be positive. a F 2013 cc CC Michael Swanbom BY NC SA Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 48.0 cm 45.6 cm 4.10 cm The moment about the upper attachment point is N-m. The moment about the lower attachment point is N-m. luk-
The cantilever beam is supported by a fixed support at A, and subjected to the force F = 550 lb and the couple M = 2870 ft-lb. Draw the shear force and bending moment diagrams (in your homework documentation) and determine the equations for V(x) and M(x). Take x = 0 at point A. c 03O 2013 Michael Swanbom F CC BY NC SA M A • B a Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value 6.2 ft 4.34 ft Support Reactions The force reaction at A is lb (take up as positive). The couple moment reaction at A is lb (take counterclockwise as positive). Shear Force and Bending Moment Equations In section AB: V(x)= lb and 'M(x)= ft-lb. In section BC: V(x)= lb and 'M(x)= ft-lb.
Handwritten solution required , including the free body diagram.
6 in 60° 20 in Statics Instructor A vertical force of P = 100 lb is required to remove the nail at C from the board. Determine the magnitude of the moment about B exerted by the 100 lb vertical force. Draw a free body diagram for the system. Then, use what you know about moments to solve for Mp What is the magnitude of the moment at point B due to P if P = 100 lb and 9 = 10"? Round to the nearest whole number. Enter a response then click Submit below lb in
The simply supported beam is subjected to the force F-600 N and the uniform distributed load with intensity w=450 N/m. Draw the shear force and bending moment diagrams (in your homework documentation) and determine the equations for V(z) and M(2). Take 2 = 0 at point A. 19 W B F 2013 Michael Swanbom BY NC SA D Χ a. -b- - Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value α 4 m b 2 m с 3 m Determine the maximum shear force (magnitude) and its location in the beam, and the maximum bending moment (magnitude) and its location in the beam. Note: On an exam, you may be required to actually sketch the shear and moment diagrams, but there is no reasonable way to assess this on WAMAP. Maximum shear stress: Vmax Maximum bending moment: Max = N located at x = m Nm located at x = m

SEE MORE QUESTIONS

Recommended textbooks for you

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Q1) Draw the shear and moment diagrams for the shaft. The supports at A and at B are journal bearings. A = lw = 100 16/6+ (4f+) = 400 lb 200 lb 100 lb/ft B 300 lb-ft 1 ft 4 ft +10+