Q1: Draw the following readings, which represent the relationship between the mass and the rate of change in bending for a 60cm long beam according to the experience of the (Determination of Young's modulus by bending of beams) where b=2.5cm and d=05cm. From the slope of the straight line, calculate the Young's modulus of beam ? M(g) = 5O, 100, 150, 200, 250 , 300, 350 , 400 S(cm) = 1, 1.8 , 2.7 , 3.7, 4.3 , 5.1 , 5.9 , 6.6 %3D

Q1: Draw the following readings, which represent the relationship between the mass and the rate of change in bending for a 60cm long beam according to the experience of the (Determination of Young's modulus by bending of beams) where b=2.5cm and d=05cm. From the slope of the straight line, calculate the Young's modulus of beam ? M(g) = 5O, 100, 150, 200, 250 , 300, 350 , 400 S(cm) = 1, 1.8 , 2.7 , 3.7, 4.3 , 5.1 , 5.9 , 6.6 %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 3 For the beam shown in the figure, a) Derive the equation of the elastic curve. b) Compute the rotation at point B. c) Calculate the deflection at point C. Y 2.7 kN.m Y 300 N/m B 3m 3m 3m 3m
DIPO Determine the slope at point B of the beam in the figure below. Assume the material's modulus of elasticity is 180 GPa, the beam's moment of inertia 360x10 mm4. 00 20 kN D 3 m 3 m 6 m A - I E=180 II !!
27 QUESTION 2 A propped cantilever beam is shown in Figure 2. Use Macaulay's method to calculate the deflection at point C and the slope at point D in terms of El. 10 KN 1 m B 20 kN/m 5 m Figure 2 C 2 m D 2 m
Problem 3 For the beam shown in the figure, a) Derive the equation of the elastic curve. b) Compute the rotation at point B. c) Calculate the deflection at point C. Y 2.7 kN.m Y 300 N/m B 3m 3m 3m 3m
Show full and clear solutions. Use the THREE-MOMENT EQUATION to answer the following question(s). 1. Determine the deflection at B 2. Make the shear force diagram of the continuous beam 3. Make the bending moment diagram of the continuous beam
Use the slope-deflection method to analyze the continuous beam shown in the Figure below. Draw the shear and bending moment diagram and sketch the elastic curve. El is constant. Show your complete solution.
A non-uniformly distributed load is carry by a 12 ft cantilever beam. What is the value of the kips maximum deflection and maximum slope of the beam if E = 30000- and in? != 8200 in*. Use Double Integration Method. 30 kips / ft 20 kips / ft A 12 ft E l is constant
rd Determine the slope at point C of the beam in the figure below. Assume the material's modulus of elasticity is 200 GPa, the beam's moment of inertia = 360x106 mm4. 20 kN D 3 m 3 m 6 m II !!
Use the conjugate beam method to determine the slopes at ends A and D and the deflections at points B and C of the beam shown in the figure. 60 k 40 k A D B C -20 ft -10 ft 10 ft El = constant E = 1,800 ksi I = 46,000 in.
A cantilever beam carries a varying load as shown in the figure. If E=200,000 Mpa and I=120x106 mm4 Determine the following. Use Double Integration Method 1. Slope at free end 2. Deflection at 4m from the free end 10kN/m 7kN/m
1. From the given figure below, determine the maximum deflection and slope of the beam. Use double Integration Method Figure1.1 18 kip / ft A 2 EI -20 ft