Q1) Choose the best answer for five only of the following 1. The minimum value of the directivity of an antenna is.......... a) Unity b) Zero 2. Very low signal strength in antenna. a) Minor lobes b) Null c) Infinite d) None c) Antenna patterns d) Major lobes 3. the maximum directivity of an antenna that normalized far field pattern is given by? ((sin cos² ) 1/2 0 ≤0≤π and 0 ≤ p ≤π/2,3π/2≤ p ≤ 2π E(0, 4) = {(si is a) 7.07dB b) 7.7dB elsewhere c) 8.7dB d) 9dB 4. the depth of penetration of 1 MHz wave in sea water which has conductivity σ = 4 mhos/meter and permeability approximately equal to that of free space is a) 25mm b) 25cm c)25m 5. The free space media can be considered as d) 25km a) Lossy media b) lossless media c) good conductor d) a and c 6. The input impedance is equal to the load impedance when...... a) 1 = 2 b) 1 = 1/2 c) 1 = 2/4 d) a and b

Q1) Choose the best answer for five only of the following 1. The minimum value of the directivity of an antenna is.......... a) Unity b) Zero 2. Very low signal strength in antenna. a) Minor lobes b) Null c) Infinite d) None c) Antenna patterns d) Major lobes 3. the maximum directivity of an antenna that normalized far field pattern is given by? ((sin cos² ) 1/2 0 ≤0≤π and 0 ≤ p ≤π/2,3π/2≤ p ≤ 2π E(0, 4) = {(si is a) 7.07dB b) 7.7dB elsewhere c) 8.7dB d) 9dB 4. the depth of penetration of 1 MHz wave in sea water which has conductivity σ = 4 mhos/meter and permeability approximately equal to that of free space is a) 25mm b) 25cm c)25m 5. The free space media can be considered as d) 25km a) Lossy media b) lossless media c) good conductor d) a and c 6. The input impedance is equal to the load impedance when...... a) 1 = 2 b) 1 = 1/2 c) 1 = 2/4 d) a and b

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Categorize the level measurement sensors as point level measurement and continues level measurement.
Draw a circuit block of a 4-1, 8-1, and 16-1 MUX. For each MUX, identify and label the data selector, data inputs, and output. Also explain the number of input and selector data of each MUX.
What is the counting method for Analog to digital conversion?
Differentiate between Bias and precision error Repeatability and reproducibility
Ultrasonic sensors are generally used in applications that require invasive measurement of level a. true b. false
D1 Q1 Do Qo CLK- Qo If the circuit above is a set of sensors, which of the following is the output function? O QOQ1X O (Q0 + Q1)(Q0 +X) QO Q1X' O (QO Q1X') O QOQ1+ Q0X
Arduino Mega is based on ATmega328 processor True False O * Arduino Uno has .... Analogue input/output 12 O 8 16 Arduino Uno processor speed is greater than Arduino Due False O True O
Microprocessor - Arithmetic Instructions
Electrical Write verilog Algorithm level code for 4:1 multiplexer
What is calibration? How do you calibrate a measurement device?
8096 has ----------- bit loop control. Option 1: 16 bit Option 2: 4 bit Option 3: 8 bit Option 4: 5 bit
Suppose R2 is a sensor whose resistance varles from 5ka to 10k0. Vs SV and R1 = 10k0. The maximum value of VD is and the minimum value of VD is R1 Vs W VD R2 O 17. 0.83 O 1.75. 1.25 O 25. 1.67 02, 13