Q1/ Casing setting depth-3000 ft. Hole Size =17 in, Casing J55 ,54.5 lbm/ft, 13 8. in OD, 12.615 in ID. Shoe joint 44 ft. Pump Capacity 0.112 bbl/stk. Cement Program: Lead Slurry(13.8 lb/gal)= 2500 ft length, Slurry yield =1.59 ft'/sk. Tail Slurry(15.8 lb/gal)= 1200 ft length, Slurry yield= 1.15 ft'/sk. Excess Volume350%. %3D Calculate: (1)Number of Lead cement sacks required. (2)Number of Tail cement sacks required.(3) Number of Mud barrels required to Pump the cement Plug. (4)Number of Strokes required to Pump the top cement Plug.

Q1/ Casing setting depth-3000 ft. Hole Size =17 in, Casing J55 ,54.5 lbm/ft, 13 8. in OD, 12.615 in ID. Shoe joint 44 ft. Pump Capacity 0.112 bbl/stk. Cement Program: Lead Slurry(13.8 lb/gal)= 2500 ft length, Slurry yield =1.59 ft'/sk. Tail Slurry(15.8 lb/gal)= 1200 ft length, Slurry yield= 1.15 ft'/sk. Excess Volume350%. %3D Calculate: (1)Number of Lead cement sacks required. (2)Number of Tail cement sacks required.(3) Number of Mud barrels required to Pump the cement Plug. (4)Number of Strokes required to Pump the top cement Plug.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4a) A Ship must discharge a total of 2200 cubic meters Sea water ballast Within 6 hours. Using S SNAME reccomended fluid Velocity, size and Select the appropriate scha 40 Steel pipe. What is the actual velocity? total head is 6) Calculate the power to drive the ballast pump in part a) if the 65m. What power would be required the ship was in fresh water? (Sea water SG: 1.025, freshwater : 17 1)
A hydraulic cylinder has these specs: Bore: 3.5" Stroke: 20" Rod diameter: 1.25" Pressure: 1800 PSI Flow rate at cylinder: 4 GPM a. What is the extension area of this cylinder? b. What is the retraction area of this cylinder? c. What is the extending force of the cylinder? d. What is the retraction force of the cylinder? e. What Volume of fluid is used when extending the cylinder? f. What is the speed of extension for this cylinder (in/min)?
The clearance hole LMC diameter formula is H @ LMC = O (H +H head) / 4 O (F-F head) / 2 O (F + F head) / 2 O (F + H head) / 4
a) Mud is flowing through 4 ½ inch OD/ 3.64 inch ID, internal flush drill pipe. The circulating flow rate is 400gpm and the mud properties as follows : Mud weight = 10 ppg Yield point = 10 Ib/100 ft² Plastic viscosity 30 cp 1. Calculate the pressure losses per 10,000 ft of drill pipe. 2. Calculate the pressure losses per 10,000 ft of drill pipe if use a water as a working fluids. 3. During the calculation case 2 at what velocity flow become turbulent?
c) A 10,000 ft string of 7 in., 26 Ibs/ft L80 casing is run in a hole filled with 12 Ibs/gal mud. The string is equipped with a float shoe. Calculate the following: i. Hook load of an empty closed-end casing string in mud. ii. Hook load of a mud-filled string in mud. iii. Hook load of 16 ppg cement-filled string in mud.
A-1: Size the duct system shown below and determine the pressure drop in each run, using equal friction and velocity methods. Bed Room Length (m) 3 (7.57kW) Segment A 2.1 Bed Room B 1.5 1 (6.72kW) 3.7 D 1.5 2.1 1.2 3.4 2.3 C 2.3 2.3 K 2.3 Q 2.3 M 2.3 2.3 Kitchen 1 (8.25kW) 2.3 4.9 1.8 K E Lounge 1 (11.30kW Bed II E Room 2 (5.74kW) G Drawing 1 (13.63kW
Place the correct formula in the blank %To determine Generated Power Output of Wind turbine clc clear all I=42; v=17; ad=1.23; cp=0.6; ng=0.96; nb=0.73; pw=0.5*ad*area*v^3 pt=pw*cp p=pt*ng*nb pmw=p/1000000 area=pi*l^3 | area=pi*l^2 || area=pt*I^2 area=p*l^2
Patm = 10^5, P(water) = 1000 kg/m^3 ; Pair = 1.2 kg/m^3 ; g = 9.8m/s^2gage pressure Pg = P - Patm
The figure below shows a mechanism that is typical the tank of a water closet. Notes that flapper C is hollow and filled with trapped air. 1. Determine the number of links, full joints, half joints, and DOF (Mobility) of the (ABC) mechanism. 2. Carefully examine the configuration of the components in the mechanism. then answer by True or False the examinations below. A D В E
Pipe Flow w/ Moody
Describe Applications of weirs in past and in present.
Water density is 1000kg/M3 Solve part a , b and c