Q1: By using the transformations of a couple, replace the three couples by one couple with the forces acting horizontally at "A" and "B? 100 Ih 100 Ib 200 Ibe 200 Ib- 50 Ib 50 Ib

Q: Calendering is a special manufacturing process in which large volumes of rolled thin plastic films…

A:

Q: What is the major benefit of cutting fluids that contain water?

A: Cutting fluids: These are the special type of lubricant and coolant used in the manufacturing…

Q: Which of the following helps to prevent the impurities and foreign materials from entering into the…

A: While poring the liquid metal into the mould it is very important to prevent the impurities to enter…

Q: What is oblique impact?

A: Oblique impact: The oblique impact can be defined as the impact on the other body with a certain…

Q: 7.Vents are used for releasing hot gases during pouring.

A: Liquid metals ,when solidifying , release a lot of hot gases. Vent holes are made to facilitate the…

Q: The Contribution of ring frame machine in the spinning industry.

A:

Q: In which casting process the sand is mixed with a thermosetting resin to form a mold? * O Squeeze…

A: Casting is a manufacturing process in which a liquid material is poured into the mold cavity .…

Q: Define mould.

A: Moulding processMolding or moulding is the process of manufacturing by shaping liquid or molten raw…

Q: can you resolve??

A: Power for first turbine Power  for second turbine To find the power output of the device and power…

Q: hat is anealing process?

A: Annealing process is the heat treatment process.

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: Advantage of Mechanical chucks is:         a/ High accessibility       b/ Good flexibility       c/…

A: advantages of mechanical chucks are It provides flexibility  in changing workpieces   . It has a…

Q: Relation between shear stress and shear rate for a tooth paste is Curve statrting from origin…

A: For a Newtonian fluid, the shear stress will be proportional to shear strain. So, for Newtonian…

Q: Describe a Propeller blade and main areas of the blade What is the main goal of the propeller?…

A:

Q: It is a fixed casting attached to the back of the lathe carriage (a) Collet attachment (b)Magnetic…

A:

Q: 3- What are the main classes of welding? 4- With drawing explain flam different types, what type is…

A: There are three primary flame types: neutral (balanced), excess acetylene (carburizing), and excess…

Q: 13- What is the function of chills?

A: Dear student as per the policy i can solve only one question for you request you to please post the…

Q: With the help of a labelled schematic diagram show the path of a warp yarn in a High Speed modern…

A: the diagram shows the path of wrap yarn in high speed modern warping machine

Q: help please. thank you Based on what you know about correct moisture content for milling (14%),…

A: Moisture content (MC) is defined as the weight of water present in a paddy or rice. Accurate…

Q: -_are small openings made into the mould through which liquid metal enters the cavity.

A: The mould cavity is given to find the entrance point of cavity

Q: What is the cutting speed of a material with a radius of 40 mm and a speed of 1000 rpm?

A:

Q: What is the advantage in casting turbine blades that have either highly aligned grain boundaries or…

A: Turbine blades are manufactured by casting by containing superalloys in them. These superalloys have…

Q: p that is the part

A: introduction: we have to describe water jet pump part of abrasive jet mechening

Q: A column of molten metal placed in the mould to feed the casting as it shrinks and solidifies is…

A: Sprue is used to feed the molten metal to the mold through laddle. Runner is a passage through which…

Q: Broaching is an example of joining process primary shaping process surface finishing process…

A: Broaching is an multiple tooth cutting operation with the tool reciprocating. It is an fastest way…

Q: In sand moulding process, a rammer is O a. A tool used in foundry to pack the sand in mould O b. A…

A:

Q: Advantage of Mechanical chucks is: High accessibility O Highest pull out security O Good flexibility

A: Chuck is a clamping device that is used to hold radial symmetry objects such as round bars or…

Q: 11) Define the cornering stiffness.

A: When the vehicle is moving at a high speed the lateral acceleration will develop in the tire due to…

Q: 1- Explain why a casting may have to be subjected to various heat treatments. 2- Describe the…

A: Given questions are related to manufacturing engineering and material science. Why a casting may…

Q: The purpose of using flux in soldering is to....

A: Use of flux in soldering: The main purpose of the flux is to prepare the metal surfaces for…

Q: 20- Which of the following metals is used for the preparation of patterns in shell molding? a.…

A: Hi. as you have submitted multiple questions and not specified which question needs to be solved, we…

Q: What does the nail spacing depend on?

A: Nails are the most common mechanical fastenings used in wood construction. There are many types,…

Q: Why should the sample be rotated 90 ° after each milling step? Explained in detail

A: During a manufacturing process,  The work piece is rotated in order to ensure the removal of rough…

Q: what is green sand and splite pattern and how to make a mould of green sand for a splite pattern…

A: Green sand is a mixture of sand, bentonite clay, pulverized coal and water. Its main purpose is to…

Q: 1. Under what conditions are straight, or non-tapering, pipe threads used?

A: Here is the solution of your question:-Explanation:Straight or non-tapering pipe threads are…

Q: B/Choose the correct answers for the following: 1- Consider the following advantages offered by…

A: Plasma arc welding    ***As per our company policy we are supposed to do only 1 question if you need…

Q: Chills are used metal . The torch size of ( GTAW ) process is larger than other ( PAW ) process . 5.…

A: Solution:   Note: Dear Student! As per our guidelines, we are only allowed to answer three sub-parts…

Q: During the direct extrusions process, which of the following type of plunger is used? O a. Both…

A: Forward Extrusion is also known as Direct extrusion. Backward extrusion is also known as Indirect…

Q: Ranking metal shaping processes by kg carbon footprint (per kg of stuff produced) which of the…

A: The Casting process is a manual process so it generates least carbon footprint.   generates the…

Q: If you were manufacturing a precision component which has a mass of around 15 grams and which was a…

A: ans : Low pressure casting Solid 3D objects made by low pressure casting all other option are…