Q1- An earthquake causes an average of 3.5 m strike-slip displacement over a 120 km long, 15 km deep portion of a transformed fault. Assuming that the rock along the fault had an average rupture strength of 150 kP, estimate the seismic moment and moment magnitude of the earthquake? - log Mo/, 5- 10.7) (M. = µAD; Mw :

Q1- An earthquake causes an average of 3.5 m strike-slip displacement over a 120 km long, 15 km deep portion of a transformed fault. Assuming that the rock along the fault had an average rupture strength of 150 kP, estimate the seismic moment and moment magnitude of the earthquake? - log Mo/, 5- 10.7) (M. = µAD; Mw :

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The center of Mohr's circle is 35 MPa, and the differential stress is 25 MPa. Calculate the values…

Q: If the shear modulus of the material along the plane is 3x10^10 Pa, area of the fault plane is…

Q: 13. The difference between the major and minor princi- pal stresses at a point is 70 kN/m². If the…

Q: Consider two series of triaxial compression test data, one for Rock A and one for Rock B. Which of…

A: As we know the elastic behavior of any material is dependent on th modulus of elasticity of…

Q: 50 MPa On tan o

A: a) From the diagram, Major Principal stress, σ1 = 104 N/mm2 Minor Principal stress , σ3 = 18 N/mm2…

Q: 1. Some geophysical (dynamic) tests were performed in the field on a rock layer, and the velocity of…

Q: Above the water table, the sand is saturated stress (in kN/m²) at point A as shown in figu 3 m 8m 1…

Q: A certain fault with a ruptured length of 504.65km and depth of 10.33km was determined to have an…

Q: A structure has a stiffness of 143 kip/in and the value of displacement in a particular earthquake…

A: The base shear can be calculated using the equation: base shear = stiffness * displacement Given…

Q: What physically happens to dynamic friction as you speed up and slow down in a velocity weakening…

A: As multiple questions are asked, By Bartleby's rule, SME are informed to answer first question as…

Q: Two vanes A and B, with length-to-diameter ratios of 3 and 1 respectively, are each used to make a…

A: VaneAlong vertical plane (KN/m2)Along horizontal plane (KN/m2)A506.671451.5B229.18687.55Explanation:

Q: 5. Deformation of a retaining wall is assumed to be as presented in the figure below. Determine: a)…

A: We need to find Active and Passive pressure at different points Active pressure is given by Pa =…

Question

100%

Q1- An earthquake causes an average of 3.5 m strike-slip displacement over a 120 km long, 15 km
deep portion of a transformed fault. Assuming that the rock along the fault had an average rupture
strength of 150 kP, estimate the seismic moment and moment magnitude of the earthquake?
log Mo/, 5- 10.7)
(M. = µAD; M,
1.5

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate the surface wave magnitude Ms for an earthquake with IMM of VII, in an area that can be approximated by a circle with radius 20 km for a site at the borders of the given isoseismal map. This site is located in the Western United States. You may use the equation given below. Compare the ensuing value with the estimates from relationships with other magnitude scales. Calculate the fault surface displacements. Assume that the earthquake mechanism is normal. M, =-1.10 +0.62 I, +1.30 -10 r, +1.62 log(r, )
Q3/ Determine the increase in vertical stress at (2.0) m below point (A) due to a surface load shown in Fig.(1), Q4/ In tu 6 m 2 m 2m 6m Aq=175 kN/m² Aq= 100 kN/m² Fig. (1) Jab
9. A rock mass is cut by one set of joints with spacing S = 0.40 m. (a) If the joint normal and shear deformations are assumed to be equal to that of the rock itself, express k, and k,, in terms of E and v. (b) Assuming E= 104 MPa and 0.33, calculate all the terms of the strain-stress relationship for an equivalent transversely isotropic medium, (corresponding to Equation 6.9).
Seismic Principle Candidate Questions. 1. Define Normal fault, Strike slip fault, and Reverse fault. 2. How is plate tectonics related to volcanoes and earthquakes? 3. Describe the relationship between Return Period and probability of occurrence for earthquake. 4. Define Ductility (Response Modification Factor) Magnitude vs Intensity of Earthquake 5. How do you measure magnitude of earthquake? 6. What is the purpose of base isolation and how? 7. Type of earthquake waves, list most destructive wave. 8. Factors affecting seismic response of structure. 9. Definition of flexible diaphragm. 10. Loading to be included in the seismic analysis 11. How is Seismic design category (SC) is related to maximum height of structure? 12. How do you construct Design Response Spectrum? 13. Seismic anchorage force for wall/floor connection. 14. What is mode shape of structure reflected in the vertical distribution of seismic shear?
In a given earthquake, structure A is weaker than structure B (structure A has a lower yield strength). Which structure is most likely to have a higher ductility demand? Structure B Cannot tell from the information provided Structure A
5. During the Mexico City earthquake of 1985 certain buildings collapsed, while others remained standing. What was the issue with the buildings that collapsed? How could these collapses have been avoided? 6. What are some other examples of resonance? How does resonance affect these different systems? 7. Structural engineers consult with geologists to help predict the expected frequency of earthquake motions at a given site. They use this information to then make sure that buildings on that site do not have the same natural frequency as the expected earthquake input motions to avoid setting up resonance, in which the displacements of the building are amplified. What are some different strategies you might use to change the frequency of a building? Is it better to design buildings that are stiffer or more flexible?
Referring to Figure Q2 (a), the vertical stress increase at point A is 25 kN/m2due to application of line loads q1 and q2. Determine the magnitude of q2.
A vane shear test was conducted in a saturated soft clay,using a 100 mm 3 200 mm vane. When the vane was rotatedat the standard rate of 0.1°/s, the torque measured inthe torque meter increased to 60 N ? m, and with further rotationreduced to 35 N ? m. Determine the peak and residualundrained shear strengths of the clay.
3. The following convergence measurements (U) have been made in a 4.6-m-diameter circular vertical shaft in good quality granitic rock mass (Em = 40 GPa, ν = 0.2): θ (deg) U (mm) 0 2.25 45 2.39 90 1.50 135 1.00 a) Derive the equations that relate convergence to in situ stress. b) The angle θ is measured (clockwise) with respect to the x-axis, which is oriented 30 degrees clockwise from True North. What is the orientation of the maximum principal stress with respect to True North?
2. Which earthquake is local in nature and rarely occurring? a) Volcanic earthquake b) Shallow earthquake c) Collapse earthquake d) Intermediate earthquake View Answer