Q1/ Acolumn of rainforced concrete has steel reinforcing rods running throughits entire length and parallel to the column axis. If concrete has (E) of 15GPaand tensile strength of 2.8 MPa and the steel rods has (E) of (210) GPa andtensile strength of(400) MPaDetermine the modulus of elasticity and tensile strength of composite if the steelrods occupy 10% of cross-sectional area of the column at:E = ?1. applied load parallel to rods2. applied load at right angle to rods3. applied load at 45° to rods8...2E

Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q1/ Acolumn of rainforced concrete has steel reinforcing rods running through its entire length and parallel to the column axis. If concrete has (E) of 15GPa and tensile strength of 2.8 MPa and the steel rods has (E) of (210) GPa and tensile strength of(400) MPa L Determine the modulus of elasticity and tensile strength of composite if the steel rods occupy 10% of cross-sectional area of the column at: E = ? 1. applied load parallel to rods 2. applied load at right angle to rods 3. applied load at 45° to rods X 8...2 E E-

Q1/ Acolumn of rainforced concrete has steel reinforcing rods running through its entire length and parallel to the column axis. If concrete has (E) of 15GPa and tensile strength of 2.8 MPa and the steel rods has (E) of (210) GPa and tensile strength of(400) MPa L Determine the modulus of elasticity and tensile strength of composite if the steel rods occupy 10% of cross-sectional area of the column at: E = ? 1. applied load parallel to rods 2. applied load at right angle to rods 3. applied load at 45° to rods X 8...2 E E-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the y-bar centroid of the composite figure shown. Where: y = 18mm and x = 9 mmShow your solution and round off if possible
The bond strength for M20 concrete as per IS 456: 2000 is 1.2 N/mm2. For reinforcing steel of grade Fe 360, the development length in terms of bar diameter (o) is
Please include photos of the tables you used.
The composite bar, firmly attached to unyielding supports, is initially stress-free. What maximum axial load P can be applied if the allowable stresses are 10 ksi for aluminum and 18 ksi for steel?
For the composite bar indicated, determine the permissible bending moment when the bar is bent about a vertical axis. Aluminum stress is 100 %3D MPa, Brass stress is 160 MPa, Eb = 105 GPa, Ea = 70 GPa Brass 6 mm Aluminum 30 mm 6 mm -30 30 mm
The trimetallic composite section in Figure 4 is compressed by an axial load P = 12 kN applied through a rigid plate. The section consists of a circular steel core surrounded by 2 brass and copper shells. The steel core has a diameter of 10mm, the brass shell has an external diameter of 15mm, and the copper shell has an external diameter of 20mm. The corresponding modulus of elasticity are Ea = 210 GPa, El = 100 GPa and Ec = 120 GPa.(a) Calculate the compressive stress σa, σl, and σc, in the steel, brass, and copper, respectively, that produces the force P.
Determine the y-bar centroid of the composite figure shown. Where x1%-68; x2=100 and y3D84 x1 x2 - y
Reinforced Concrete
Aggregates used to make concrete could be Gravel or Crushed stone or even recycled Aggregates. Select one: O True O False Lowering the w/c ratio of concrete lead to an increase of the strength but reduces the workability and tendency to segregation and bleeding. Select one: O True O False
For a continuous and oriented fiber-reinforced composite, the moduli of elasticity in the longitudinal and transverse directions are 19.7 and 3.66 GPa (2.8x10 and 5.3x 105 psi), respectively. If the volume fraction of fibers is 0.42, determine the moduli of elasticity of fiber and matrix phases. Em- E₁= i GPa GPa
1. Three metal strips, each 40 mm height, are bonded together to form the composite beam shown. The modulus of elasticity is 210 GPa for the steel, 105 GPa for the brass, and 70 GPa for the aluminium. If the allowable bending stress for the aluminum (Gallow)al= 100 MPa, for the steel (Gallow)s=150 MPa and (Gallow)b= 200 MPa for brass determine the maximum allowable intensit of w of the uniform distributed load. 2w Aluminum 2w 10 mm Brass 10 mm Steel 20 mm 2m - 40 mm
I need the answer as soon as possible