Q1/ A steel wide flange beam has the dimension shown in the figure, if it is subjected to a shear of V=80KN, a-plot theshear-stress distribution acting over the beams cross-sectional area, and b- determine the shear force resisted by the web.80 kN20mm15mm200mm20mm300mm Q2/ The beam shown in the fig. is made from two boards. Determine the maximum shear stress in the glue necessary tohold the boards together along the seam where they are joined. The supports at B and C exert only vertical reactions on thebeam.6.5 KN/m* ISO Mm y 3ommN150mmBC30mat2m2 m.4 m%23

Since the Question number to be solved is not stated, the solution for Question No.01 is as follows:…

Q1/ A steel wide flange beam has the dimension shown in the figure, if it is subjected to a shear of V=80KN, a-plot the shear-stress distribution acting over the beams cross-sectional area, and b- determine the shear force resisted by the web. 80 kN 20mm 15mm 200mm 20mm 300mm

Q1/ A steel wide flange beam has the dimension shown in the figure, if it is subjected to a shear of V=80KN, a-plot the shear-stress distribution acting over the beams cross-sectional area, and b- determine the shear force resisted by the web. 80 kN 20mm 15mm 200mm 20mm 300mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the shear strain xy at corners A, B, C, D if the plate in Figure 5 distorts as shown by the dashed lines. Consider small strain assumption. 3 mm 300 mm y D 4 mm 400 mm- 12 mm B A mm 8 mm $2 mm X
In the figure below, the 1300-kg uniform bar AB is suspended from two cables AC and BD each with a cross-sectional area of 410mm2. The stresses in AC and BD are limited to 110MPa and 53MPa, respectively. Find the magnitude P of the largest additional vertical force that can be applied to the bar.___________kN in 2 decimal places Take note: Write it on a paper, hand written showing correct answer.
A 52-kip force acts on a machine part at point A as shown below. The diagram shows the internal normal force, shear force and bending moment acting on a particular RECTANGULAR Cross section. -30in N 10in 26in F=52 kip The value of the bending moment M you would use to find the bending stress on a stress element located 2 inches up from the bottom of the rectangular cross section is closest to: 264 kip-in O a. 408 kip-in Ob. 1,464 kip-in O c. 1,608 kip-in
Maximum allowable (safe) bending stress for a beam AB under a constant distributed load as shown in the figure.It is 40 MPa.a) What is the maximum value of the length (L) of the beam in this case?b) Draw the shear stress (τ) profile where the V (shear in section) force is greatest.Hint: You can specify several points in the section and calculate the shear stress for those points.
Bronze Steel Steel W = 40 kips %3D 2 ft 2 ft 2.
What torque is applied to the end of the shaft in the figure, resulting in a 3 degree rotation? The shear elastic modulus of steel is G = 80GPa.
The wide-flange pinned-end column shown in the figure carries two loads, a force acting at the centroid P₁ = 450kN and a force P₂ = 270kN acting at distance s = 100 mm, from the centroid. The column is an HE 240B shape with L = 4.2m, E = 200 GPa, and Oy = 290 MPa. (a) What is the maximum compressive stress in the column?
For a beam with a cross section of equilateral triangle of side length a= 20 mm, (a) draw the shear and moment diagrams and determine the maximum values of shear and moment throughout the beam. (b) Determine the maximum tensile and compressive bending stresses and the locations they occur. 150 N/m 10 N.m A В C O 00 100 mm 200 mm 300 mm 80 N
Q1: The beam shown in Figure 1 is subjected to a vertical force Pv and a horizontal force Ph. The data for Pv, Ph, a,L,and e are shown in Table 1. Determine the maximum compressive and tensile stresses under the vertical force (at a distance a from the left support.) Pv = 80k N a = G0o 6 omm e %3D 26 K N 120 mm L =3600 mm Figure 1 250 mm
Question 2) Find the shear center of the section below and calculate the maximum shear stress that occurs in the section as a result of the loading shown in the figure. The section thickness is uniform everywhere and is 10 mm. Note: G.M is the geometry center of the section, the shear force of 40 kN acts from the geometry center of the section. You can look at your lecture notes for the coefficients you will need. 160 mm V-40 kN t LG.M 100 mm
The beam is subjected to a bending moment of M = 17 kN. m. σA = B 200 mm OB = 30 mm 30 mm M 30 mm 30 mm 50 mm 150 mm 150 mm 50 mm Part A Determine the bending stress in the beam at point A. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in the case of tension. ANSWER: Q Tap image to zoom Part B Determine the bending stress in the beam at point B. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in the case of tension. ANSWER: