Q1 a)) Describe what is meant by a passband communication system. b)) What is line coding and why is it used in communication networks? i) Assuming maximum line voltages of +V and -V, sketch the Bipolar, Non-Return-to-Zero line code for the binary sequence: 010010. c)) Assuming Manchester Coding where the low-to-high phase represents a zero and the high- to-low phase represents a one, decode the 7 binary digits encoded in figure Q1. COMME Figure Q1

Q1 a)) Describe what is meant by a passband communication system. b)) What is line coding and why is it used in communication networks? i) Assuming maximum line voltages of +V and -V, sketch the Bipolar, Non-Return-to-Zero line code for the binary sequence: 010010. c)) Assuming Manchester Coding where the low-to-high phase represents a zero and the high- to-low phase represents a one, decode the 7 binary digits encoded in figure Q1. COMME Figure Q1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What do you understand by the term phase containment of errors? Explain with example.
For Amplitude Modulation, Emitter modulator ________a) Operates in class C modeb) Has a low efficiencyc) Output power is highd) Operates in class B mode
a) The Channel is a key component to consider in all communications systems. Give two examples of a channel commonly used in communications systems, and for each, the key properties that can impact transmission. Compare twisted-pair and fibre-optic wired channels. Explain how the use of differential signals can be used to improve the signal to noise ratio in a twisted pair channel. i) ii)
Q4) A-Ten telephony signals that have the same limited Bandwidth frequency of 2000Hz are sampled equally by the Nyquist rate, then TDM multiplexed and transmitted simultaneously in one channel. Calculate 4 a The time spacing between adjacent samples. b. The minimum required Bandwidth for TDM transmission. c. The minimum required sampling rate (Nyquist rate) of the resultant TDM signal. (06
C. Phase reversal D. Modulator's sensitivity factor 39. In linear modulation, the intelligent signal is conveyed in A. The amplitude of the transmitted signal BA The sideband components of the transmitted wave C. The phase deviation modulated signal D. None of the above | 40. What communication technique or modulation scheme make use of channel noise as an added advantage? A. Asynchronous shift key modulation B. Vestigial sideband modulation C. Spread-spectrum D.4 Wideband Frequency modulation |41. Narrowband FM and AM share a lot of similarities except that , A+ The lower side frequencies are 180° out of phase. B. The upper side frequencies are 180° out of phase. C. The sideband frequencies are 180° out of phase. D. None of the above | 42. Modulation is done in , A. Transmitter B. Radio receiver C. Between transmitter and radio receiver D. None of the above |43. At 100 % modulation, the power in each sidebands is, A 50 % В. 40 % С. 60 % D 25 % | 44. In a TV transmission, picture is…
Detail the operation of a Variational Autoencoders (VAE). How does this compare to a standard Autoencoder (AE). Clearly indicate the composition of the Loss function in this network.
In digital communications broadband means a bandwidth: a. lower than El (2Mbps); b. lower than 64kbps; c. higher than El (2Mbps); d. this is not specified.
9-A binary data source has P(OT) = 3/8, due to interference of channel, then P(OR/1T) = 1/16 and P(1R/0T) = 3/4. Calculate the noise and losses entropies and compare with source entropy.
Consider a telephone line initially noiseless channel having bandwidth and signal level determined by the network engineer. Calculate maximum data rate. After certain distance the channel becomes extremely noisy, so that the noise is strong which faints the signal .Calculate the capacity of the channel.
How could I get the thevnin voltage from this using the transfer funciton and the lookback method?
Don't need to elaborate the answer. Just write down the correct answer. Some questions may have multiple answers. 1) Which multiplexing technique shifts each signal to a different carrier frequency? a) FDM b) TDM c) WDM d) PDM 2) Which multiplexing technique involves signals composed of light beams? a) FDM b) TDM c) WDM d) PDM 3) We need an addressing mechanism in a) Satic b) Parallel c) Synchronous d) Statistical 4) Pulse stuffing is a strategy used in a) TDM b) FDM c) FHSS d) WDM 5) a) FDM b) TDM technique uses multiple carrier frequencies. c) WDM d) FHSS e) DSSS TDM. 6) We need to use synchronous TDM and combine 20 digital sources, each of 100 Kbps. Each output slot carries 1 bit from each digital source, but one extra bit is added to each frame for synchronization. Answer the following questions: i) What is the size of an output frame in bits? a) 10 b) 20 c) 21 d) 11 ii) What is the output frame rate? a) 200000 frames/sec b) 210000 frames/sec c) 10000 frames/sec d) 100000…