Q1: A 50HZ,11KV,3-ph,alternator with earthed neutral has a reactance of 50\ph and is connected to bus bar through a C.B.The distributed capacitance up to C.B between phase and neutral is 0.01µF,Determine: 1-The restriking voltage across the contacts of the breaker, 2-The frequency of oscillation, and 3-The voltage across the capacitance.

Q1: A 50HZ,11KV,3-ph,alternator with earthed neutral has a reactance of 50\ph and is connected to bus bar through a C.B.The distributed capacitance up to C.B between phase and neutral is 0.01µF,Determine: 1-The restriking voltage across the contacts of the breaker, 2-The frequency of oscillation, and 3-The voltage across the capacitance.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

6. The instantaneous value of an alternating current is 5 mA at a displacement angle of 60°. Determine the following: a) its peak value; b) its peak-to-peak value; c) its effective value and its average value.
You are an electrician working in an industrial plant. A 30-hp three-phase induction motor has a current draw of 36 amperes at full load. The motor is connected to a 480-volt line. A three-phase wattmeter indicates a true power of 22 kW. Determine the power factor of the motor and the amount of capacitance needed to correct the power factor to 95%. Also determine the minimum voltage rating of the capacitors. The capacitors are to be connected in wye.
Construct a graph to represent the recurring nature of partial discharge pulse sequences under sinosoidal alternating voltage (applied voltage) using internal discharges as a typical example. The graph should consist the voltage accross the dielectric, voltage across the void and current impulses.
A synchronous generator generates 365 V at 60 Hz when the field current is 3.9A. The e.m.f generated when the frequency is 40Hz and the field current is 2.1A is ...............
4. An alternating current varying sinusoidally with a frequency of 50 Hz has an ms value of 40 A. Find: a. The instantaneous value of 0.0025 seconds after passing through maximum positive value, b. The time measured from the maximum value when the instantaneous current is 14.14 A.
A 12V rms ac supply is connected to the primary winding of a transformer with a turns ratio of 0.052. calculate the RMS secondary voltage given a voltage regulation of 4.0%.
Determine the PIV and dc output voltage in the Figure. The transformer has a 26 V rms secondary voltage rating, and the line voltage has a frequency of 60 Hz.
Q9
Sine wave A has a positive-going zero crossing at 40°. Sine wave B has a positive-going zero crossing at 45°. Determine the phase angle between the two signals. What signal leads ? A Y-connected system can have wires. The (resultant) voltage between the hot legs (135V) is The phase angle between the phase voltage and the line voltage of a A-connected generator is degrees. The phase current produced by a certain 20V, Y-connected generator is 12A. The corresponding line current is A certain A-connected generator produces phase voltages of 30V. The magnitude of the line voltages are When the turns ratio of a transformer is 20 and the primary ac voltage is 6V, the secondary voltage is If 20W of power are applied to the primary of an ideal transformer with a turns ratio of 8, the power delivered to the secondary load is The turns required to match a 500 source to a 1000 load is
Q4 A 11 kV, 500 MVA alternator is connected to a slow C.B. through a bus-bar. Determine the three ratings of the C.B, the average RRRV, and the oscillation frequency knowing that it reaches the peak re-striking voltage with 100 µs time.
56. A single phase thyristor adjust line spacing converter with a resistive load is shown below: V₂ = V sinest SCR ER R V₂ (B) 1.11 (D) 1.44 If the supply voltage is 230V (rms) at 50 Hz, calculate ripple factor for firing angle a-45" and R - 100 9. (A) I (C) 1.21
3. If the ratio of V/F has been kept constant and the observed value of hysteresis loss at rated frequency of 50 Hz is 18 W, the measured value of core losses is 35 W, Find the total core losses at the frequency of 60 Hz. 02: