Q1: 220V, 7 Hp DC series motor coupled to a fan, the motor draws 25 A and runs at 300 rpm at terminal voltage of 220V and no external resistance, torque of the fan is proportional to the square of the speed, if Ra30.6 N and Rf-0.4 2. (Neglect rotational losses): a) Determine the power supplied to the fan and torque developed by the motor. b) The speed is to be reduced to 200 rpm by inserting external resistance. determine the value of this resistance and the power delivered to the fan.

Q1: 220V, 7 Hp DC series motor coupled to a fan, the motor draws 25 A and runs at 300 rpm at terminal voltage of 220V and no external resistance, torque of the fan is proportional to the square of the speed, if Ra30.6 N and Rf-0.4 2. (Neglect rotational losses): a) Determine the power supplied to the fan and torque developed by the motor. b) The speed is to be reduced to 200 rpm by inserting external resistance. determine the value of this resistance and the power delivered to the fan.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A shunt DC motor is supplied by 520V terminals voltage and is used to supply a mechanical load with rotating speed of 1000rpm. The armature is wave-wound and has 500 conductors. The useful flux per pole is 0.03Wb and there are 4 poles (2 pairs of poles). The armature resistance is 0.4 Ohms. Calculate: 1.The internal emf of the motor. 2.The armature current. CLEAR AND CORRECT OR DISLIKE
A 200 V D.C. shunt motor takes 20 A at rated voltage and runs at 1000 r.p.m. Itsarmature resistance is 0.1 ohm. Calculate the value of additional resistance requiredin the armature circuit to reduced the speed to 800 r.p.m when the load torque isindependent of the speed.Ignore the field current. (Ans.1.98 ohm)
Q22/ A three phase induction motor with supply frequency of 50 Hz , 10 poles. If the slip is 4 % at a certain load, determine (a) the synchronous speed, (b) the speed of the rotor (c) the frequency of the induced e.m.f in the rotor and speed of the induction motor if the slip changes to 5.75 %
Q1 Describe the Characteristics, characteristics, efficiency calculations, their applications Of DC Motors in detail
4. For a full-wave phase control circuit draw the output voltage and current waveforms when firing angle α = (45-X) °. (Here X= 1813)
I need the answer as soon as possible
Please answer alll subparts in short for like either dislike
A DC motor should be operated in a strong field which is due to the What happens to if suddenly goes a) nothing, it continues rotating b) it over speeds c) it stops rotating current if moter if rotating to zero. as before
both parts fast plz don't answer 3.00 pm
B3. A three-phase, 60 Hz 4-pole induction motor has a slip of 0.05 when the output is 30 kW. The frictional loss at shaft is 300 W. Calculate the following: (i) the rotor speed in r.p.m. (ii) the torque delivered by the rotor. (iii) the torque delivered to the rotor. (iv) the rotor IR loss.
A DC series motor having a resistance of 0.4 ꭥ and runs at 2000 rpm when connected to 250 V supply and drawing a current of 20 A. (i) What resistance must be added in order to limit the speed to 4000 rpm when armature current is 5A? Assume flux varies linearly. (ii) What resistance must be added to limit the speed to 1000 rpm when armature current is 30 A? Assume that the flux at 30 A is 20% more than that at 20A. (iii) At what speed the motor will run if it is connected directly to 250 V supply when the load is such that the current drawn is 30 A?