Q.5/(8)Marks: Consider a closed - loop transfer function-K(s-1)s3+3s? +(2-K)s+KT(s) =Use Routh criterion to find the range of K such that the system is stable.

Answered: Image /qna-images/answer/a9d677fe-6d0e-453c-a4e6-170a723c1b60.jpg

Answered: Q.S/(8)Marks: Consider a closed - loop…

Q.S/(8)Marks: Consider a closed - loop transfer function -K(s-1) T(s) = s3+3s2+(2-K)s+K Use Routh criterion to find the range of K such that the system is stable.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: The following control system is given. R is the input and C is the output. Blocks are 3 and H(s) =…

A: In this question we need to find the close loop and open loop transfer function of the given system

Q: -Deler Ie he traISIer TUNCUOI UT me COMTOT Systelmgiven I igure Delow, and derive an expression for…

A: Given block diagram Transfer function is the ratio of laplace of the output to laplace of the input…

Q: The closed loop system is given below. What is the K gain for the system to be stable? should be in…

A: We need to find out the range of k for a stable system.

Q: A plant has a transfer function 1 G₁(s)= (s+5) (s+10) and is going to be controlled using a…

A: Given, the plant transfer function is,Phase Margin = The required proportional-integral controller…

Q: Q1: Comment on each step you need to obtain the second order transfer function which gives the…

Q: Assume that there exists an LTI system S that transforms {x[n]) = {n} into {y[n]} = {n-u[n]}. s Show…

A: Given: A discrete-time LTI system S with input x[n] and output y[n] is described as xn→S→yn=n·un…

Q: Q35. If the open-loop transfer function of the system is K(s + 10) s(s+ 8)(s + 16)(s + 72) G(s) H(s)…

Q: For an inverting operation amplifier shown below: If the input and the output signal are continuous…

A: For an Ideal OP AMP : 1 ) Input impedance is infinity hence currents flowing through input terminals…

Q: 4 N(s)=D(s)=0. The plant transfer function is: P(s) Consider a Proportional (P) Control…

Q: Q1. In a digital signal processing technique, an analog signal needs to be sampled wisely into a…

A: A discrete signal is given byw[n]={1,2,3↑,2,−1} ;Here, ′↑′ indicates the index, n = 0.We need to…

Q: Q2. Convolution and conversion between time and frequency domain are integral parts in biomedical…

A: Part (a) xn=1,1↑,1,2 hn=1↑,2,0,2,1

Q: 1. Why continuous signal is to be converted in discrete domain?

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: What is the angle deficiency (in degrees) to be contributed by the lead compensator at the desired…

A: Q1 needs to be solved in order to solve Q2 to get the desired pole locations. The desired pole…

Q: For an inverting operation amplifier shown below: If the input and the output signal are continuous…

Q: 2. The signal y[n] is the output of an LTI system with impulse response h[n] for a given input x[n].…

A: Given Data:The pole-zero plot in the Z plane for two stable sequences,Input andOutput To Find:ROC…

Q: G, R(s) C(s) G2 H2 H1 Figure Q3

A: For the given block diagram, the closed loop transfer function is calculated by using block…

Q: The discrete-time signals in Figure below are plotted as shown (a (a)- plot the following: i-…

A: Step 1: Step 2: Step 3: Step 4:

Q: Problem) (Camplex The transfer function f plant is given s, Engineering 10 S(S+5) Drauw Yoot locus…

A: Control systems are represented by transfer function. This can be written in both time domain and…

Q: For the open-loop transfer function below, apply Nyquist Stability Theorem to the design controller.…

A: The main difference between an open-loop and a closed-loop system is that a closed-loop system can…

Q: how to find the closed loop poles and zeros on a tf like this by hand. With unity feedback.

A: Calculation of closed loop poles and zeroes for the given unity feedback transfer function.The…

Q: Q1) For the control system shown in figure (1). Obtain the transfer function C(s)/N(s) assume the…

Q: For an 8-bit SAR ADC, find the output code if Vref = 10 V and Vin = 4.95 V 00110001 01111111…

Q: Given ₁ [n] = () 2u[n- 3]use DTFT to x a) [ find the signal X₁(e). b) [ Given x₂[n] = 8[n+3] - 36[n…

A: Given: Two Discrete sequences and we have to compute the DTFT. In third part, DTFT is given and we…

Q: Find the transfer function T(s) = C(s) / R(s) for the diagram below using block diagram reduction.…

Q: Consider the closed-loop transfer function B+ kB2 T(s) = B3+ kB4 where B1, B2, B3, and B4 are…

A: Choose the correct option Closed loops transfer function is given. Find the sensitivity of transfer…

Q: Q1: Comment on each step you need to obtain the second order transfer function which gives the…

Q: Convert the following block diagram to Signal Flow Graph and apply Mason's Rule to calculate the…

A: We need to find out transfer function by using of Mason's gain formula.

Q: The signal s(n)s(n) is recorded with frequency sampling Fs=500HzFs=500Hz. What's the duration of…

A: Given: The signal s(n) is recorded with frequency sampling Fs= 500Hz.

Q: Q2/ The Nyquist plot of the open-loop transfer function K(T₂S + 1)(T₂S + 1).... (Tms + 1) GH(s) = sn…

A: The Given Data is The Nyquist of the open-loop transfer function. GHS=Kt1S+Lt2S+L-------tmS+LSnis…

Q: Q24. For the system shown in the figure Q24, Obtain i the closed loop transfer function, ii i.…

A: Given open loop transfer function is G(s)=20(s+1)(s+4)=20s2+5s+4 Feedback given is unity feedback.…

Q: BLOCK DIA (d) 10s +1 T(s) = s( - 2s + 10) Ans. unstable, unstable (e) 4(s + 2)s? (s +6) T(4) Ans.…

Q: Problem 4. Considering the four different responses recorded at different occasions to a step input…

A: The given step responses are shown below. These 4 different step responses have been recorded for…

Q: -1, 1, 0, 1<n<4 SInl, 0, -3 < n< 3 x (п) y(n) -4 <n< -1 — elsewhere elsewhere

Q: For the control system shown below, find the value of K₁, K2 and K3 if the system transfer function…

A: The control system block diagram is shown below,

Q: B-8-2. Consider the system whose closed-loop transfer function is C(s)___K(T₂5 + 1) R(s) T₁s +1…

Q: Example 3: Simplify the block diagram shown in the figure, and obtain the transfer closed-loop…

A: The given Block diagram is shown below,

Q: 1.382 x 108 2. A system has transfer function G(s) = s2 + 628.3s + 9.87 × 106' (a) Sketch a…

Q: 5. Find the close-loop transfer function, T(s) = C(s)/R(s) for the system shown using block diagram…

A: given that a block diagram of the system is

Q: semi-log facsimile and draw asymptotic Bode plots (magnitude & phase

A: draw asymptotic Bode plots of the given transfer function. 1. Magnitude 2. phase

Q: 19. Using Mason's rule, find the transfer function, T(s) = C(s)/R(s), for the system represented in…

A: Using mason gain formula find the transfer function for the system represented in Figure.We know:

Question

Q.5/(8)Marks: Consider a closed - loop transfer function
-K(s-1)
s3+3s? +(2-K)s+K
T(s) =
Use Routh criterion to find the range of K such that the system is stable.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

This subject is control systems of ece pls solve fast
Consider the system shown in Figure (1). This is a PID control of a second-order plant G(s). For the disturbance input in the absence of the reference input, the closed-loop transfer function is given as below: Ca(s) S D (s) (s + 10) (s² + 4s + 16) Rewrite the transfer function of PID controller in following form: 1 Ge(s)= K₂ (1+: + Tas) Tis R(3) K(as+1)(bs+1) PID controller D(s) Figure (1) +3.68+9 Plant G(s) C(s)
Q2 i) Find DTFT of a) X[n]= δ[n+5] -αn δ[n-5] b) X[n]=(n-1) (1/3)n u[n] please solve step by step subject:signal and systems
K A certain analog plant function is shown in figure 2 and its transfer function G,(s) = (s+a)(s+b)· This plant is sampled using a zero-order hold (ZOH) before the signal is fed to a digital controller. Using 0.45 second as sampling time and K=14; a=3; b=5, Do the following. Zero-order Plant Plant Hold ZOH Gp(s) G(z) Figure 2 i. Obtain the z-transform G(z) ii. Discuss the importance of a ZOH in digital control systems
Need correct answer and by hand solve plzzz ??
Please solve No. 2 below. Please provide a clear and readable solution. I appreciate any help you can provide. The course subject is Feedback Control Systems. NOTE: Convert the following system to signal flow graph and solve for the transfer function using Mason’s Rule. Thanks!!!
Realize an asynchronous counter circuit that counts as 3->5->4->0->9->4.
For the transfer functions given in the control system in the figure, find the relevant E(s) steady state error and approximately draw the response curve for the relevant input. Note: Find the kaher state error ess and the permanent state response yss and show the rise time tr, peak time tp, settling time ts, maximum overshoot M and steady state regions on the curve you drew.
What are the various methods of power system fault analysis, and how are faults cleared in a timely manner?
Given the signal flow graph: 1. How many forward paths are there from R(s) to C(s)? 2. How many pairs of non-touching loops are there? 3. Are there three non-touching loops? True/False
The simplified block diagram for position servo mechanism used in the base of arobotic arm is illustrated in Figure. Investigate whether each of this statement iscorrect or false by using root locus approach.(i) The break-away point of the system is at –0.835
Given G₁ = 4(s+8) /(s+3)(s+7) and G₂=2s /(s+10) function write an m-script to determine the final transfer i. Series ii. Parallel iii. Feedback, taking G₂ as the feedback element