Q.6. A plate 450 mm x 150 mm has been placed longitudinally in a stream of crude oil (Sp. gravity 0.925 and kinematic viscosity of 0.9 stoke) which flows with velocity of 6 m/s. Calculate: (i) The friction drag on the plate (ii) Thickness of boundary layer at trailing edge. (iii) Shear stress at the trailing edge.

Q.6. A plate 450 mm x 150 mm has been placed longitudinally in a stream of crude oil (Sp. gravity 0.925 and kinematic viscosity of 0.9 stoke) which flows with velocity of 6 m/s. Calculate: (i) The friction drag on the plate (ii) Thickness of boundary layer at trailing edge. (iii) Shear stress at the trailing edge.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Estimate the drag force on the fuselage shown below for a cruising speed of 210 m/s at 10,000m. Hint 1: To calculate the drag force split the fuselage into 4 parts: front hemisphere,cylindrical body, vertical stabilizer, back hemisphere. Model the front and back hemispheres as flow over a sphere. For simplicity treat the cylindrical body and vertical stabilizer as flat plates.Hint 2: Use Cd vs Reynolds number graphs for sphere and flat plate. If your Reynolds number is greater/smaller than the Cd vs Reynolds graph range, you can instead use the greatest/smallest number available on the graph.
HOME WORKS 1. A hydrofoil 0.366 m long and 1.82 m wide is placed in a water flow of 12.9 m/s, with p = 1025.3 kg/m and v =1.02x 106 m/s. Estimate the boundary layer thickness at the end of the plate, and the friction drag from the leading edge.
Air flows over a flat plate with a velocity u = 13 m/s and temperature T. = 25 °C. The plate surface area and temperature are A = 2 x 2 m and T, =125 °C, respectively. a- Determine the critical length X (length of the laminar region). b- Determine the rate of heat transfer in the laminar region. %3D C- Determine the total rate of heat transfer from the entire plate (mixed boundary layer). Use the following properties of air H = 2.08 x 10 N.s/m, p = 0.887 kg/m, k = 0.0325 W/m.K, Pr = 0.705 %3D rinar @111
Help me step by step
Need Solution through 15min
P6.31 (a) A luxury sports car has a frontal area of 2.08 m? and a 0.29 coefficient of drag at 95 km/h. What is the drag force on the vehicle at this speed? (b) A sport-utility vehicle has Cp = 0.45 at 95 km/h and a slightly larger frontal area of 2.70 m?. What is the drag force in this case?
A thin flat plate 20 cm by 90 cm is immersed in a 1m/s stream of water at 20 °c ( density=998, viscosity=0.001)the stream is parallel to the long side, compute the total friction drag considering both front and back sides of the plate
Problem 4: Truck Trailer What wind velocity is required to topple an empty tractor trailer, as shown here? The trailer is 48 ft long, 8 ft wide, 12 ft tall, and the trailer floor is 4 ft above the road surface, giving the trailer a square cross section. It weighs 13,500 lb. Assume the airp = 0.0023 slug/ft³ and kinematic viscosity v = 1.5 ×10+ ft²/s.
A space 22 mm wide between two large plane surfaces is filled with honey with absolute viscosity 0.16 N.s/m2 . What force is required to drag a very thin plate of 0.6 m2 area between the surfaces at a speed, v = 0.22 m/s(i) if this plate, t is equally spaced between the two surfaces? (ii) if t = 3 mm?
Assume the stabilizer of an airplane is a flat plate. If the transition /critical RN 750,000, what is the skin-friction drag of a rectangular stabilizer having a span of 1.73 m and a chord of 0.81 m at a speed of 44.7 meters per second? Assume standard sea level conditions.-round off to 4 decimal places-show complete solution