Q.6) Oil (μ= 0.02 Pa.s and SG=0.9) flows through a horizontal commercial steel pipe (d=4" and E=0.045 mm) at a velocity of 0.5 m/s (see drawing). Determine the total head loss that occurs over its length and 3 long radius elbows (K=0.5). Pipe size (4¹) K = 0.5 elbow 1 10 m 20 m 10 m 10 m

Q.6) Oil (μ= 0.02 Pa.s and SG=0.9) flows through a horizontal commercial steel pipe (d=4" and E=0.045 mm) at a velocity of 0.5 m/s (see drawing). Determine the total head loss that occurs over its length and 3 long radius elbows (K=0.5). Pipe size (4¹) K = 0.5 elbow 1 10 m 20 m 10 m 10 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Shown in the figure below is a pipe system (commecial steel pipes) having a given centerline geometry is to be used to transfer oil from Tank A to Tank B at a rate of 1.70 cubic meter per minute. Minor losses from the pipeline are due to 2 pcs-90o elbows (K = 0.5) ; Contraction (K = 0.05) and Expansion (K=1). If the oil has a density of 801.3 kilogram per cubic meter and viscosity of 2.394x10 -2 kilogram per meter per second, the diameter of the pipe in millimeter is Blank 1 mm. *Express your answers in whole significant figure without decimal value and without unit*
Please check attach file
What’s the answer for this please ?
For a fully developed laminar flow of water (dynamic viscosity 0.001 Pa-s) through a pipe of radius 5 cm. the axial pressure gradient is -10 Pa/m. The magnitude or axial velocity (in m/s) at a radial location of 0.2 cm is 11/11
60m 44m (2) (1) (3) 40m (4) 40m (5) 42m c) Find the flow discharge within the system. (6) 30m 35m Q (2). You have a tank open at the top, flow in the 25-cm-smooth-65 m long- plastic pipe. (7)
The water is delivered with piping system given in the figure below. The levation difference between entering section and tank is 143,55 m. Estimate the gage pressure [MPa] at point 1. (Note: For water at 20°C, take p=998 kg/m and u=0.001 kg/ms. ) 5 cm diameter cast-iron pipe Length of the system is 1.2 km All fittings are flanged. The vohume flow rate is 300 L min 45 treaded elbow Yanit
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m^3/s is to occur in the cast iron pipe. Use f= 0.0021 for all pipes. (DO NOT ROUND OFF)
Question 3 Water flows through a 2-in.-diameter (5.08 cm) tube that suddenly contracts to 1 in. diameter (2.54 cm). The pressure drop across the contraction is 3.45 kPa. Determine the volume flow rate. Minor Loss Coefficients for Pipe Entrances Entrance Type Reentrant Minor Loss Coefficient, Ka 0.78 Square-edged Rounded "Based on h-K(V2/2), where V is the mean velocity in the pipe. Contraction loss coefficient, K [ h = Kc \ /² ] 0.5 r/D K 0.02 0.06 ≥ 0.15 0.28 0.15 0.04 Contraction Expansion A1 A2 A₂ AR Ag/A = AR = A₁/A2 1.0 0.8 0.6 0.4 0.2 0.2 о T ° 0 0.2 0.4 0.6 0.8 1.0 Area ratio, AR 1.0 OOOO 0.8 0.6 Expansion loss coefficient, K Loss coefficients for flow through sudden area changes.
A horizontal smooth-walled cylindrical pipe has diameter 0.04 m. Water flows along the pipe with a flow rate of Q 2 x 10-4 m³ s-¹. = For water, take the kinematic viscosity as v = 10-6 m² s¹ and the 10³ kg m-³. density as p = (a) Calculate the Reynolds number and establish whether the flow is turbulent or not. (b) Show that λ = 0.035 is a good approximation of the Darcy friction factor for this flow. (c) Calculate the shear stress at the wall of the pipe, and hence find the magnitude of the drag force exerted by the water on a length 2 m of the pipe. L =
Q1: An oil with a viscosity of µ=| 0.37 N.s and density p=860- kg flows in a m? pipe of diameter D= (0.035) m. Find a) What pressure drop, R-P,, is needed to produce a flow rate of Q= (4.0*105) m³ if the pipe is horizontal with X, = 0 and X, = 17 m ? b) How steep a hill, must be pipe be on if the oil is flow through the pipe at the same rate as in part (a), but with P =P,? c) For the conditions of part (b) if P = 200 kpawhat is the pressure at section X = 6m, where x is measured along the pipe? Find. N Арat L —> 6т —()
Water at 80°F flows from a storage tank through 618 ft of 6-in Schedule 40 steel pipe, as shown in the figure. Taking the energy loss due to friction into account, calculate the required head hin feet above the pipe inlet to produce a volume flow rate of 1.65 ft³/s. (round the final answer to three significant figures) h 6-in Schedule 40 steel pipe pipe length
Dev