Q.6/A 300 hp tractor towing tired trailer is climbing a uniform 6.5% slope on steady speed 9 mph,the rolling resistance is 170 Ib/ton. The single-axle tractor weight 72000 Ib, and the trailer weight 52000 Ib.the combined weight distribution is 57% on the drive axle. What is the ability to move the tractor? If not.what do you suggest to the moving up? Discuses that according to the coefficient of traction.

Given, P = 300 hp G = 6.5% V = 9 mph R = 170 lb/ton Wt = 72000 + 52000 = 124000 lb

Q.6 /A 300 hp tractor towing tired trailer is climbing a uniform 6.5% slope on steady speed 9 mph, the rolling resistance is 170 Ib/ton. The single-axle tractor weight 72000 Ib, and the trailer weight 52000 lb. the combined weight distribution is 57% on the drive axle. What is the ability to move the tractor? If not, what do you suggest to the moving up? Discuses that according to the coefficient of traction.

Q.6 /A 300 hp tractor towing tired trailer is climbing a uniform 6.5% slope on steady speed 9 mph, the rolling resistance is 170 Ib/ton. The single-axle tractor weight 72000 Ib, and the trailer weight 52000 lb. the combined weight distribution is 57% on the drive axle. What is the ability to move the tractor? If not, what do you suggest to the moving up? Discuses that according to the coefficient of traction.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 1.2 Find the horizontal thrust W₁ C y H X¹ h -"7" B H
When will a three-force member be considered in equilibrium? A When they are coplanar. B All of the above When the sum of the two forces is equal to the third force. D When they are concurrent or parallel.
A simply supported 4-m long beam is made up of 80% grade Malugai. The beam is carrying a uniform load of 11 KN/m all through out its length and a concentrated load of 600 N at the midspan. The cross-sectional area of the beam is indicated below. ... 190 mm 50 mm 180 mm 150 mm 40 mm 190 mm Determine the following:
Can you help me about this problem?
A horizontal bar, 11 ft long and of negligible weight, rests on rough inclined planes as shown. The coefficient of friction for all contact surfaces is 0.27. What is the normal force at contact point A? How close A may the 120 lb force be applied before motion impends?
3. A 100-kg crate is being pushed by a horizontal force F, with a magnitude defined by the second degree curve below. If the coefficients of static and kinetic friction between the crate and the surface are µ; = 0.2 and ps = 0.10, respectively, determine the total time it takes for the force to move the crate 50 m from its initial position. F F=kr 500N F 2s
A,B,&C please and thank
To unload a tied pile of plywood from a truck, the driver first tilts the truck bed and then accelerates from rest. Knowing that friction coefficients between the bottom plywood layer and the bucket floor are s 0.40 and k 0.30, determine (a) the smallest acceleration of the truck that will cause the plywood pile to slide and (b) the acceleration of the truck that makes corner A of the plywood pile reach the end of the bucket in 0.9 s. I need the calculations and a detailed description substantiated and explaining each step of the calculations. Please. (If you have any way to make it easier to translate, I appreciate it. I can't read very well in english)
A simply supported 4-m long beam is made up of 80% grade Malugai. The beam is carrying a uniform load of 11 KN/m all through out its length and a concentrated load of 600 N at the midspan. The cross-sectional area of the beam is indicated below. ... 190 mm 50 mm 180 mm 150 mm 40 mm 190 mm Determine the following:
A cooper strip of 200mm width and 300mm thickness is to be rolled to a thickness of 295mm. The roll of radius 300mm rotates at 100rpm.the average shear strength of the material is 180MPa. The roll contact length and the roll force
In a lifting machine in which velocity ratio is 30, a load of 5000 N is lifted with an effort of 360 N. Determine whether it is self-locking or reversible machine. How much is the frictional resistance?
Current Attempt in Progress Plot the magnitude of the resultant R of the three forces as a function of 0 for 0 ≤ 0≤360°. After you have the plot, determine the value of 0 which makes the magnitude R of the resultant of the three loads (a) a maximum and (b) a minimum. Record the magnitude of the resultant in each case. Use values of = 64° y = 22°, F₁-59 N, F₂ = 129 N, F3 = 71 N. Answers: (a) maximum R= i N when 0= i (b) minimum R = i N when 0- i