Answered: Q.5 – A simple Rankine cycle works…

Q.5 – A simple Rankine cycle works between pressures (28 bar and 0.06 bar). The initial conditions of steam being dry saturated. Calculate : i- cycle eff. ii – work ratio | -

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Give an Example of a problem on Actual Reheat rankine cycle with complete solution and compare it…

Q: 1. In an Ideal Rankine Cycle, the steam throttle condition is 4.1Mpa and 440C. If turbine exhaust is…

A: Given:Pressure and temperature at turbine inlet, P1=4.1 MPa and T1=440°CPressure at turbine exhaust,…

Q: Assume an Otto cycle with compression ratio of CR = 9 1. The intake air is at 100kPa, 20°C, and the…

A: Given:compression ratio, r=9P1=100 KPaT1=20°C =293 KV1=500 cm3 =500*10-6 m3T4=800 KCp=1.01…

Q: Q 3) An engine working on U cycle has a Compression ratio of IS and Cutt- off takes place at 5% of…

A: Given: Compression ratio: →r=15=V1V2 Because cut off takes place at 5% of the stroke. Hence cut off…

Q: has a Q5) An Oil engine working on the dual-Combustion Cycle Cylinder diameter of 25 cm and stroke…

A: Given data as per the question Length of stroke =36 cmdiameter =25 cm

Q: 1. A steam power plant operates on a simple ideal Rankine cycle. The steam enters the turbine at…

Q: assuming point 1 is at the pumpe entrance. and determine the required power to operate the pump,…

Q: 2) The compression ratio of an ideal Otto cycle is 7 and prior to compression air is at 285K and…

Q: An engine, using 1.5 kg of air as working fluid operates in an air-standard Otto cycle. The initial…

Q: Enlist and Draw (only) the modifications made in Rankine cycle on T-S diagram. Also draw the flow…

A: Modification made in Rankine cycle: In the modified Rankine cycle the pump work is neglected.…

Q: Brayton Cycle: 18. An air standard Brayton cycle operates with compression ratio of 6 and…

Q: 2. In an Ideal Rankine Cycle, the steam throttle condition is 8Mpa and 480C. If turbine exhaust is…

A: The stepwise procedure to solve this problem is shown in the following attached image:

Q: an ideal Otto cycle with a compression ratio of 8. Find the efficiency of the cycle with the high…

A: The pattern of the Otto motor is known as the Otto cycle. It is the one of most normal thermodynamic…

Q: 1. a. derive expression for thermal efficiency and backwork ratio for the Rankine cycle

A: Derivation of thermal efficiency Heat addition q1=h4-h2 Heat rejection…

Q: Prove that there is an increase in efficiency between a Simple Rankine Cycle and a Reheat Rankine…

Q: In a standard brayton cycle, the heat added is 20kW while the heat rejected is 8k. Find the pressure…

Q: A steam power plant operates between a boiler pressure of 58 bar and a condenser pressure of 0.05…

Q: We wish to model a gasoline engine for an automotive application with the ideal Otto cycle. The…

Q: A simple Rankine cycle works betw een pressures 43 bar and 10 Kpa, the initial condition of steam…

Q: An idealised Rankine cycle with superheat is shown below. 2 a. Show on the diagram (or describe as…

Q: A Bryton cycle with regeneration using air as the working fluid operates between 880 and 95 KPa as…

Q: The efficiency of a Brayton cycle is 28.5 %. What is the pressure ratio? (assume adiabatic index as…

A: Above cycle in T-S diagram is a brayton cycle which includes 4 processes:- 1-2 → Isentropic…

Q: 3-a- establish an expression in terms of the volume ratio of compression for the ideal thermal…

Q: A reheat steam cycle has 13,580 kPa of throttle pressure at the turbine inlet and a 37.50308414 atm…

A: Given data: Cycle : Reheat steam cycleThrottle Pressure = 13580 kPaReheat Pressure = 37.50308414…

Q: The compined cycle plant shown in figure uses a gas turbine engine operating with 250 kg/s of air…

Q: A Simple Rankine cycle works between pressures 38 bew 383 bar anod ond Ta bar, bhe instial…

Q: 1.There are compressed 100 m/min of air from p=100kpaa and t=24°Cto p-534 kpaa. determine a) Wa, Waf…

Q: An Otto cycle with a compression ratio of 7.5 operates from the suction conditions 14.2 psia, 85 °F.…

A: Given Data Compression ratio=7.5 P1=14.2 psia T1=85°F=545°R

Q: quickly solve with me time 30 minutes...In an ideal Bryton cycle gas turbine unit, air is drawn in…

A: A gas turbine operates on the Brayton cycle. It comprises adiabatic compression, constant pressure…

Q: In a standard Brayton cycle, the heat added is 20kW while the heat rejected is 8kW. Find the…

Q: 1.)An ideal otto cycle has a compression ratio of 9..A t the beginning of compression,air is at…

A: Note: As per the Bartleby guidelines, only three parts of a question can be answered at a time.…

Q: A diesel cycle has an initial temperature of 270C. If cut off ratio is 2.5 and a compression ratio…

Q: Q3 An oil engine working on the dual-combustion cycle has a cylinder diameter of 25 cm and stroke of…

Q: Q3. An engine operate on air standard Otto cycle with a compression ratio of 7, Determine: 1. The…

Q: 3. A Diesel Cycle operates with compression ratio of 14 and with cut-off ratio occurring at 5% of…

A: Given Compression ratio, r = 14 Initial volume, V1 = 1.5 ft Find Cut-off ratio, rc

Q: 18. A steam engine receives saturated steam at 260°C. Steam is released when its specific enthalpy…

A: When an amount of force act on the object, it has the ability to change its diaplcement, so the…

Q: 1. A Carnot Cycle expan sion stroke, the pressure goes From 2 Mpa to 1 Mpa ond it has a temperature…

Question

Q.5 - A simple Rankine cycle works between pressures (28 bar and 0.06
bar). The initial conditions of steam being dry saturated. Calculate :
i- cycle eff.
ii – work ratio
|
iii- specific steam consumption

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A stear power plant operates bstween a boller pressure of 52 bar and a condenser pressure of 0.045 bar. Calculate for these Imis he cycle afficiency for a Rankine cyce with dry saturated steam at entry to the turbine.
A simple Rankine cycle works betw een pressures 73 bar and 10 Kpa, the initial condition of steam being dry saturated. Calculate the cycle efficiency, work ratio and specific steam consumption.
1. A reheat steam cycle has 13.65 MPa pressure at the high pressure turbine inlet and a 2500 kPa reheat pressure, the temperature at the inlet of the high pressure turbine and reheat temperature of the steam is 540 °C, condenser pressure is 3.4 kPa, engine efficiency of high pressure and low pressure turbine are both 75 %. Sketch the cycle lay out and cycle T-s diagram. a. Find the enthalpy at each state point. (Summarize) b. Find the actual enthalpy at the exit of the high-pressure turbine and low-pressure turbine. Find the cycle thermal efficiency С. d. If the net power at the turbine is 100 MW find the mass flow rate of steam, in kg/s; Heat rejected by the condenser, in MW е.
Q.5 A vapour compression heat pump is driven by a power cycle having a thermal efficiency of 25% for the heat pump, refrigerant 12 is compressed from saturated vapour at 2 bar to consenser pressure 12 bar. The isentropic efficiency of compressor is 80% saturated liquid entors the expansion value of 12 bar for power cycle 80% of the neat rejected by it is transferred to the heated space which has total heating requirement of 500 kJ/min. Determine the power input to heat pump compressor F 12 properties are
Please give detailed solutions and steps clearly Thank you
ı need solution
A simple Rankine cycle works betw een pressures 57 bar and 10 Kpa, the initial condition of steam being dry saturated. Calculate the cycle efficiency, work ratio and specific steam consumption.
No. 1 only
Given in Table are the pressure and temperature of the steam as it enters the turbine as well as the pressure in the condenser. The given engine operates on a simple ideal Rankine cycle, calculate the unknowns in Table. Show solution Rankine Pressure of Temperature Pressure at the Net work Heat Thermal entering the Efficiency (n) in % the steam entering the entering the condenser system (WN) boiler (Qin) turbine (Rx) turbine (t+) in MPa Engine of the steam done by the in KJ/kg in KJ/kg (Pe) in kPa in °C A 3 350 75
.) An Engine operating using the ideal Otto Cycle receives air at 15 psia and 75 F, then compresses it to 1.76. The total heat added during heat addition process is 352 Draw the PV and TS diagrams. Solve Btu lb for: the remaining temperatures, QR, Wnet, efficiency and how many lb of air is required if the engine is rated 500hp?
A simple Rankine cycle works betw een pressures 48 bar and 10 Kpa, the initial condition of steam being dry saturated. Calculate the cycle efficiency, work ratio and specific steam consumption.