Q.4) For the beam and loading shown in figure, draw shear force and bending moment diagrams, show all details values, distance, 12 kN/m 2 m 3 m 3 m B line or curve. 60 kN

Q: There is a structure composed of beam (AC) and truss (BD) as shown in the figure below. After trying…

A: E=29000kips/in2 To find displacement at B and C

Q: A у C n - Х 60° 40° B F = 800 lb

A:

Q: Study of forces on a body at r called_. a. Dynamic body O b. Rigid body O c. Kinematic body O d.…

A:

Q: Q2: Determine completely the resultant R of the three forces shown in the figure below. 60 kN 100 kN…

A: Given that:

Q: Find the force in member GD. 0000 40 kN 40 RN 30000 300 1.0000 10000

A:

Q: Which of the following gives the reaction at A of the simply supported beam in Newton? 10KN/m 10KN/m…

A:

Q: Force can be characterized by O Point of application O Direction Magnitude All the above

A: Given data: force can be characterized by a) point of application, b) direction c)magnitude d) all…

Q: The piece of rubber is originally rectangular. Calculate the average shear strain Yxy at A if the…

A: Given data in question Cross section 400 mm and 300 mmDisplacements 3 mm and 2 mmTo find out Average…

Q: Determine the centroidal y-coordinate (in mm, round=off to 2 decimal places) of the volume shown. 5…

A:

Q: Explain this briefly (statics of rigid bodies)

A:

Q: The following picture represents a bridge comprised by a continuous horizontal beam AB that has been…

A: As per rule only one question is to be solved As per above diagram Number of reactions at A = 2, VA…

Q: Example 4 Two structural members, one of which is in tension and the other in compression, exert the…

A:

Q: Q.21 A shaft is made up of partly solid section and partly hollow section as shown as figure. b b…

A:

Q: Refer to the figure, what is the horizontal reaction of support A in kN

A:

Q: A

A:

Q: A homogeneous disk with a radius of 9 in. is welded to a rod AG with a length of 18 in. and of…

A: Given: A homogeneous disk with a radius of 9 in. is welded to a rod AG with a length of 18 in. and…

Q: What is the horizontal and vertical component

A: To find horizontal and vertical component of 3kN force

Q: 1. COMPUTATION OF REACTIONS 2. SHEAR AND MOMENT DIAGRAM

A: Sign conventions :   Shear force force: Clock wise : +ve Anti clock wise: -ve   Bending moment:…

Q: 4 - A rubber material is attached between two rigid plates. If the lower plate is held in place,…

A:

Q: The state of stress at a point in a member is shown on the rectangular stress element in (Figure 6)…

A: Given: The stress along the x-axis is 17 ksi. The stress along the y-axis is 20 ksi. The shear…

Q: Calculate the resultant moment of the force at the point A for the beam shown in the figure below.…

A: Given beam:- Free body diagram,

Q: For the figure shown, What is the maximum tensile stress in the beam? Hint: There will be two…

A:

Q: 4) A stepped shaft composed of a solid circular aluminum with G 28 GPa and a hollow circular steel…

A: Given, There is A shaft connected in a parallel condition is given in the question. Our aim is to…

Q: Yg Z.. 200 mm ly G 20 mm 20 mm 200 mm

A:

Q: Don't copy paste

A: The maximum triangular load on web = 10Ksi The maximum triangular load on flange = 10Ksi The…

Q: Q.1 Flexural Formula A mild steel plate of width 120 mm and thickness 10 m is nest into an arc of a…

A: A mild steel plate-Width b=120 mmThickness t=10 mmRadius of the circle R=10 m=10000…

Q: 10. Given the figure, determine the moment of inertia about the y-axis. y-axis X-axis 3 6

A:

Q: Q.12 A solid shaft of diameter 'd' and length " is subjected to torque T. Another shaft B of some…

A: given For solid shaft A-diameter=dLength=LTorque=TFor solid shaft B-diameter=2dLength=LTorque=2T

Q: Sketch a flowchart showing the steps involved in the analysis of: Shear in Doubly Symmetric Shapes

A: the main steps involved in Doubly Symmetric Shapes is From Chapter 2 of ASCE/SEI 7, calculate the…

Q: The flywheel A rotates clockwise under the action of a 700 N-m couple. A band break is to be used to…

A:

Q: The shear modulus of a material is half of its Young's modulus. What is the value of its Poisson's…

A: Given, Shear modulus is half of young's modulus  i.e, ==> 2G = E To calculate: Poission's Ratio…

Introduction to Engineering Design

Students are often confused with engineering and design. The term engineering design has two words with different meanings, engineering, and design. The term engineering implies applications of laws and principles of science to design and analyze physical structures and components. In civil engineering, students apply the concept of physics and chemistry to design and build structures and buildings. In engineering disciplines, the term design means determining the dimensions, loads, and associated influences on the component due to the applied loads such as stresses and deformations. The estimation of such parameters is crucial to make the component or structure foolproof.