Q.3: Two separately excited DC generators are connected in parallel to supply a total load current of 200A. The two generators have the following parameters: G1: Ra = 0.2 N , and induced E.M.F=400 V %3D G2: Ra = 0.5 , and induced E.M.F=460 V Find Mathematically: (i)The bus-bar voltage, The armature current of each generator, (ii) The sharing power of each generator (iii)If it's required to operate generator1 at maximum efficiency and at Vbus-bar-400V. What is your opinion to achieve that? Resolve the problem. Note: The constant losses of G1=5kW.

Q.3: Two separately excited DC generators are connected in parallel to supply a total load current of 200A. The two generators have the following parameters: G1: Ra = 0.2 N , and induced E.M.F=400 V %3D G2: Ra = 0.5 , and induced E.M.F=460 V Find Mathematically: (i)The bus-bar voltage, The armature current of each generator, (ii) The sharing power of each generator (iii)If it's required to operate generator1 at maximum efficiency and at Vbus-bar-400V. What is your opinion to achieve that? Resolve the problem. Note: The constant losses of G1=5kW.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(b) A synchronous generator connected with an equivalent circuit of Figure Q4 is shown as below. Here, the armature resistance is being ignored. The field current is adjusted so that the terminal voltage is 480 V at no load. Develop and sketch the output phase voltage vs. load current characteristics of the generator under these condition as below: - i) 0.8 p.f. lagging load for 10 A, 30 A and 60 A load current ii) 0.8 p.f. leading load for 10 A, 30 A and 60 A load current Based on the characteristies as above, explain the changes of output phase voltage from the generator. Suggest the method to overcome of the instability of output phase voltage as shown? RA IA 0.2 2 j1.0 2 RF VF LF Figure Q4: Synchronous generator equivalent circuit
Solve it quickly please
A long-shunt d.c. compound generator supplies 100A at 290V. The resistance of armature, series field and shunt field windings are 0.04, 0.07 and 55 ohms respectively. Find the emf generated. The armature current la The generated voltage Eg
A 10 pole wave wound shunt generator delivers 178 A at a terminal voltage of 236 V. Ra and Rsh are 0.035 Q and 44 Q respectively. Neglecting brush drop, determine the armature current and generated voltage. Armature Current Generated Voltage
What do you call the plot of the internally generated voltage vs. field current at a given rotational speed of a DC generator? This plot is used to determine its output voltage for various field current values and/or rotational speed. A Load characteristic curve B Magnetization curve C Saturation curve
A d.c. A shunt generator delivers a load current of 80 A at 400 V. Its armature and field resistances are 0.20 and 100 respectively. Stray losses are 1500 watts. So find (1) mechanical (2) electrical and (3) commercial efficiency.
A long shunt cumulative compound dc generator delivers a load current of 60A at 440V. The shunt field resistance , series field resistance and armature resistance are 80, 0.9 and 0.4 respectively. Calculate the induced emf and load resistance.
A separately excited D.C. generator has armature circuit resistance of 0.15 . When running at 900 r.p.m., it delivers a current of 95 A at 200 V to a load of constant resistance. A) If the generator speed drop to 800 r.p.m., with field-current unaltered, find the current delivered to load. B)With what load resistance will the current be 95 amp, at 800 r.p.m.?
A shunt generator supplies a 32kW load at 215V through cables of resistance, R= 118m2. If the field winding resistance, Rf =542 and the armature resistance, Ra =42m2. Determine the following below: The terminal voltage is, The e.m.f. generated in the armature is,
A shunt generator supplies a 31kW load at 230V through cables of resistance, R = 104mQ. If the field winding resistance, Rf =68N and the armature resistance, Ra =46m2. Determine the following below: The terminal voltage is, The e.m.f. generated in the armature is,
A separately excited generator has no-load voltage of 125V. A certain load rated at 1200W, 120V is then connected at the terminal. Calculate the series resistance needed to connect to the armature circuit in order for the load to operate at rated condition if the armature resistance is 0.0692Ω.
Magnetization curve 2 280 240 200 160 120 80 40 1 2 3 5 Magnetomotive Force, mmf (A-t/pole x1000) Figure 3(b) Magnetizing curve of non-compensated DC machine Generated EMF(V)