Q.3 Determine the absolute maximum transverse shear stress in the beam. 6 kip 3 kip 6 in. ft

Q: E-11 The aluminium alloy wing section shown is subjected to a pure torque of 100kNm over its 10m…

A: The given data is shown below: Torque=100 kN-mLength=10mG=30 GPa

Q: A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal…

A:

Q: 2. The major and minor principal stresses at the point are 3 MPa and -3 MPa respectively The maximum…

A: To find out the maximum shear stress at the point.

Q: Problem Sets - 3: The cast iron inverted T-section supports two concentrated loads of magnitude P as…

A:

Q: The lapjoint is connected by three 25-mm-diameter rivets. Assuming that the axial load P= 75 KN is…

A: Given:- The lap joint is connected by three rivets having a diameter = 25 mm Axial load distributed…

Q: Determine the maximum shear stress in the strut if it is subjected to a shear force of V = 20 k

A: Given data  Shear force V = 20 k

Q: A W 12 X 35 steel cantilever beam is subjectedto an axial load P =10 kips and a transverse loadV =15…

A: Given data:- V=15 Kips =15×103 lb L=6 =6×12=72 inP=10 Kips=10×103 lb   In the given section W12X35…

Q: 3m В G P E 3m C D

A:

Q: Determine the maximum compressive bending stresses (MPa) in the beam shown

A: Moment in portion AB:

Q: The prismatic bar has a solid circular cross section with 2-in. radius. Determine the average normal…

A: Given data : Radius (r)=2

Q: Find the stresses at points A and B. 0.75 30 kv 2 S.lid

A:

Q: The cantilever beam, whose loading condition and cross-section are given in the figure, is ideal…

A:

Q: 9-14. The state of stress at a point is shown on the element. Determine (a) the principal stress and…

A:

Q: 2. Determine the maximum tensile and compressive bending stress in the beam if it is subjected to a…

A:

Q: A 116.79 kips (B 172.79 kips 92.79 kips A 119.38 kips B 40 kips 1.5" V 40 kips C From the figure,…

A: dia of rod AB=2''allowable stress in rod AB=55ksi

Q: For the truss shown, assume a cross sectional area of each member is 3.2 in? a. Calculate the stress…

A:

Q: A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 660 mm2. If…

A:

Q: The major and minor principal stresses at a point are 3 MPa and -3 MPa respectively. The maximum…

A: Given: The major principal stress, σ1 = 3 MPa The minor principal stress, σ2 = -3 MPa

Q: Find normel stress at pontA ? Find shear stren at puint A point A ? 2

A: We have to find Normal and Shear stresses at point A

Q: ed (stress SS specified to ssing tend SSI

A:

Q: Determine maximum shear stress

A: Introduction : The given section is rectangular section . The maximum shear stress in rectangular…

Q: Draw Mohr’s circle and determine the principal stresses.

A: Given Data: The stress acting along X-direction is σx=30 MPa (Tensile). The stress acting along…

Q: Problem: The state of strain at the point on the gear tooth has components &x = 750 x 106 in/in, Ey…

A: Given data :   Find : a) The in- plane principal strain? b) Max. in-plane shear strain and the…

Q: -57. Determine the principal stress, the maximum in-plane shear stress, and ver 120 MPa MADARAKAN…

A: Given data : The value of normal stress in X direction σX=300 MPa The value of normal stress in Y…

Q: 4. Draw the NA and stress diagrams (da, d., o,) for the case given below.

A: In the given figure it is clearly mention the position of compressive load ie, at the corners of the…

Q: Minimum shearing stress and maximum torsional stress occur at the center of the circular shaft under…

A:

Q: 15. Principle plane is a plane on which the shear stress is O(A) Zero O(B) Minimum OCC) Maximum O(D)…

A: Principal plane is a plane at which their is no stress stress . In Mohr  circle principal stress…

Q: Q- The normal stresses on the two mutually perpendicular planes at a point are 120 MPa (Tensile) and…

A: Given data -  Normal stress ,σx = 120 MPaσy = 60 MPa Shear stress ,τxy = 30 MPa Find -  Principal…

Q: Steel links having the cross section shown are available with different central angles B. Knowing…

A:

Q: The corners of the square plate deform as indicated. determine the angular strain at A with respect…

A: The given figure is shown below:

Q: The members of the truss are 25mmx50mm in cross section. Determine the maximum load P that can be…

A: we have to determine the maximum load P

Q: 3. (c) A square steel bar of dimension 50 mm × 50 mm × 150 mm is subjected to an axial load of 250…

A: Size of bar 50mm x 50mm x 150mm P = 250 kN or 250,000 N

Q: x K lokn зм 5 KN 3m зм 3m

A:

Q: Solve any Problem on flexure stress formula for beams

A:

Q: Try to write out the stress boundary conditions of the cantilever beam. ( not include the fixed…

A: Three force are there on cantilever beam   F force, UVL load and q force.....

Q: the bars and truss have a cross section of 250mm^2. If thr maximum average axial stress in any bar…

A: Given :

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.