Q.3) (a) Find the support reactions of the beam shown below. (b) Sketch the shear-force and bending moment diagrams for the loaded beam shown below without formulating the SF and BM equations. Also label the values of shear-force and bending-moment at all key points. y 750 N 300 N/m 600 N/m 550 N-ml A В 2 m- -1m- -1 m* 2 m

Q.3) (a) Find the support reactions of the beam shown below. (b) Sketch the shear-force and bending moment diagrams for the loaded beam shown below without formulating the SF and BM equations. Also label the values of shear-force and bending-moment at all key points. y 750 N 300 N/m 600 N/m 550 N-ml A В 2 m- -1m- -1 m* 2 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3)
Q.2) (a) Calculate the support reactions of the loaded beam shown below. (b) Write equations for w(x), V(x) and M(x) of the beam using singularity functions. (c) Sketch the shear-force and bending moment diagrams for the beam for the beam using the Graphical method. Label the values of shear-force and bending-moment at all key points. 120N/m 300 N 300 N-m 200 N 100N/m Im B 4m C Im DIm E 4m 1m G 400 N¬m
A thin beam with a solid rectangular cross-section is loaded as shown in Figure Q7 below. W W L/3 L/3 L/3 Figure Q7 What is the ratio of the maximum to nominal shear stress for the beam described in Question 7? O a. 3:2 O b. 1:4 Ос. 3:1 O d.2:1 O e. 1:2 O f. None of the provided answers are correct. O 8. 1:1
Problem 1: The figure shown is a beam subjected to varying loadings and a point load. a) Determine the magnitude and direction of the single equivalent force to the forci shown. Specify its location on the beam from point B. b) Calculate for the support reactions at A and R Fi 17kN 4kN/: 7.9 kN/m -5 m 6.7 m 2.8kn
Find the maximum moment of the given load train at point n on the beam given in the figure?
Question 5 T/2 В 1200 Nm A homogeneous steel shaft (G=83GPA) is loaded as shown in the above Figure. Assuming T = 300 N-m, determine the torsional force in N-m in Member BC. Note: Include sign (+/-), assuming the direction of Torsion (T) at D is positive Given: AB: Length = 1.75m, Diameter = 75mm BC: Length = 1.50m, Diameter = 60mm AB: Length = 1.00m, Diameter = 40mm
1 1 20 ft 18 k 10 ft 15 ft constant El Part B 10 k 2 3 15 ft Determine the reactions and the member end forces for the beam shown in A1 using the matrix stiffness method (Problem 17.4 of Structural Analysis, 6th Edition, Aslam Kassimali).
Read the question carefully and give me the right solution with clear calculations.
4.)show complete solution, final answer should be in two decimal only, i will automatically give upvote.
Figure 6 demonstrates a cantilever shaft is fixed at A and free to rotate at its right end at F. The shaft is made from steel and consists of variable diameters. for segment CF, consists of a hollow shaft and has an inner diameter of 10mm. A torque of 150 Nm, 335 Nm, and 80 Nm is applied at B, D, and E respectively. The modulus of rigidity of shafts is 95GPa. i) determine the torsion for each segment ii) show the torsion diagram for shaft iii) determine the largest shear stress developed in the shaft iv) calculate the twist of the angle at points D and F for the shaft.
sub-part