Q.2) A page of a level book with some missing readings is reproduces below. Fill in the missing entries along with the necessary arithmetical checks. RISE FALL Station BS IS FS RL (+) (-) REMARKS 1 3.650 108.260 2 2.750 3 2.830 4 3.640 2.420 СР 6. 2.410 1.320 7 2.320 3.000 Negative reading indicates staff held -2.170 against ceiling 10 2.750 11 1.320 TOTAL= 6.49

Q: tiate between focus and epicenter

A: solution of above problem is below:

Q: Profile Level Notes: The elevation of BM A = 366.65' BS (plus sight) on BM A = 3.85' IFS (minus…

A:

Q: Draw the influence line for the force in (a) member HI, (b) member FI, and (c) member EF.

A: The most common loads acting on a structure are dead load and live load. For live loads, the…

Q: 8) 900 N/m Determine the reactions at the beam supports for the given loading. 400 N/m 1.5 m 0.4 m…

A:

Q: Load (kN) Elongation (mm) Please state your assumptions and show all your work clearly. 0.0125…

A: For the given data construct the table as shown below.

Q: 1) Compute the centroid x bar and y bar of the shaded area. 12" to

A:

Q: Draw the sectional front view (front section) and draw the orthographic projection (sideand top…

A: Asked: To draw the orthographic projection views of the given object.   The orthographic projection…

Q: Water flows through a horizontal branching pipe as shown at a rate of 280L/s. All points are inside…

A: P1=70kPa Q=280L/s A1=0.1m2 V3=6m/s To find pressure at section 3

Q: 3. Starting from rest, the cable can be wound onto the drum of the motor at a rate of vA = (3t) m/s,…

A:

Q: Four forces are applied to the machine component ABDE as shown. Replace these forces with an…

A:

Q: The assembly shown is welded to collar A that fits on the vertical pin shown. The pin can exert…

A:

Q: Differential Leveling Prepare and complete the differential level notes for the information shown…

A: To Prepare and complete the differential level notes for the information shown. And to Do the…

Q: Three horizontal forces are applied as shown to a vertical cast iron arm. Determine the resultant of…

A:

Q: 1. If column AB is made from high strength pre-cast concrete and reinforced with four 20 mm diameter…

A: Given: σallowConcrete=18 MPaσallowSteel=170 MPa

Q: Q.1) The following consecutive readings were taken with a level and a 4 meter levelling staff on a…

A: Formula used :  HI = Elevation + BS  Elevation = HI - FS or IS  Staff height is 4 m. So whenever…

Q: Determine the maximum moment of a 8.4 meter long simple beam carrying a uniformly varying…

A: Draw a simple beam as follows. Write the equilibrium equation of sum of vertical forces.…

Q: The force applied at the handle of the rigid lever causes the lever to rotate clockwise about the…

A:

Q: A pontoon is to be used to transport a load across a lake. The following data are provided: Pontoon:…

A:

Q: C If after many years of operation at Re = 105, the pipe's inner surface becomes rough with an…

A: Given, Re = 105  Roughness height, ε = 0.2 mm    NOTE : From recommended matches,     Velocity when…

Q: 44. What is the difference between hydraulic conductivity and permeability? a. hydraulic…

A: 44. Option A  Hydraulic conductivity depends on both soil and fluid properties. Hydraulic…

Q: 8. The computed latitude and departure of line AB are 0.00m and + 45.46m respectively. What is the…

A:

Q: The parcel of land is shown with the coordinates at points A, B, C, D, and origin at point O. Find…

A:

Q: When discussing most efficient section in open channels, what is the perimeter, P as a proportion P…

A: Given data- Most efficient trapezoidal channel- Width=B, Height=h, Side slope= 1 V : m H, To Find-…

Q: Two parallel 40-N forces are applied to a lever as shown. Determine the moment of the couple formed…

A:

Q: y Knowing that the tension in rope BC is 500 N and the tension in rope BD is 800 N, determine the…

A: Co-ordinates of points; C=(0,0.7,1.2) D=(0,0.5,-0.3) B=(1.6,-0.6sin30o,0.6cos30o)…

Q: If the coefficient of variation of rainfall values at 4 rain gauge stations is 30% and permissible…

A: Coefficient of variation of rainfall Cv=30%Rain gauge stations n=4Permissible error in the…

Q: 7:46 AM O 0.6KB/s .illa 3. A uniform slender rod, 3.0 m long and weighing 490 N, rotates in a…

A:

Q: The 6-m pole ABC is acted upon by a 455-N force as shown. The pole is held by a ball-and-socket…

A: Free body diagram:     γB=3j     γC=6j   ⇒CF→=F→-C→            =-3-0i^+0-6j^+2-0k^…

Q: The rectangular plate is subjected to the deformation shown by the dashed line. Determine the 3. 150…

A:

Q: 22- Which of the following symbols is a representation of a Manhole in Civil 3D? A) B) M S D) S IM…

A: 22. Option C is correct .

Q: Find the total area

A: Consider the figure,

Q: A fillet weld of size 6mm used to weld a plate of width 75mm to gusset plate to transfer a factored…

A: Size of weld=6 mm,Width of plate=75 mmFactored load=120 kN,Site weld case, Fe410 steel,Welding is…

Q: Describe the three tripod system?

A: Brief concept- The three tripod system is used in the surveying. It is a very useful instrument for…

Errors in surveying

An error in surveying is defined as the difference between two or more values of an identical quantity. However, the estimates are never accurate and there will always be a degree of variability regardless of the research tool or method used. These differences are known as errors that need to be reduced or eliminated to maintain certain levels of accuracy. Even if you carefully follow the prescribed test procedures, the considerations may contain errors.