I need the answer quickly Q.11A bolt is under an axial thrust of 9 kN and transverse shear force of 5 kN.Calculate the diameter of bolt according to the theory of maximum strain energy. Take o, = 250 N/mm2,= 0.3 and factor safety = 2.8. Assume uniform distribution of normal and shear stress on cross-section.

Answered: Image /qna-images/answer/e9393700-278f-4462-af33-d3d2472b31d6.jpg

Answered: Q.11 A bolt is under an axial thrust of…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider the following figure. hị h A B (a) Determine the maximum tensile stress o, and maximum compressive stress o, (in MPa) due to the load P acting on the simple beam AB. Data are P = 6.8 kN, L = 3.4 m, d = 1.03 m, b = 80 mm, t = 25 mm, h = 120 mm, and h, = 90 mm. (Use the deformation sign convention.) MPa 0. = MPа (b) Find the value of d (in m) for which tensile and compressive stresses are the largest. What are these stresses (in MPa)? (Use the deformation sign convention.) = p MPa MPa
Q-1 A circular bar is to withstand a bending moment of 10 kNm and a torque of 30 kNm. Determine the diameter of the bar if the yield stress of the material is 250 MPa and the factor of safety is 3. Use maximum normal strain theory of failure. Take Poisson's ratio as 0.3.
Calculate the design moment strength Mu for the following section. Take f'c = 40 MPa. Sketch the strain and stress distribution diagrams for each section and try to work out your solutions using equilibrium conditions. Yield stress for N bars is 500 MPa. 75 700 60 1500 T 4N28 450
show the complete solution
The lap joint is connected by three 20-mm diameter rivets. Assuming that the axial load P= 50 kN is distributed among the three rivets, find the shear stress in each rivet. the bearing stress between the plate and a rivet. the maximum average tensile stress in each plate. Express your answer in MPa
The curved bar shown has a cross section of 30 x 30 mm. Knowing that the allowable compressive stress is 175 MPa, determine the largest allowable distance a. Take P= 4.5 kN. В. A. P P 30 mm 20 mm 20 mm 30 mm The largest allowable distance a is mm.
What are appropriate relations established from the calculation of maximum shear stress in a thin circular tube? 4 (b) t = (a) Tmax Tavg 3 'avg max 3 4 S Rỉ + R2R1+ R3 (c) Tmax when (R, = = 2avg - R.) (d) Tmax 3 A Rỉ + R? Here, (R, > R1) and S is shear force at the cross sectional and A is cross sectional area.
What is the shearing stress developed at the neutral axis of the beam with a circular cross section having a diameter of 17 mm and a shear force V = 29 kN. Assume that the shearing stress is uniformly distributed across the neutral axis. Answer must be in MPa.
For the cantilever beam shown. find the value of Normal stress due to axial :load at point A 4 KN 6 KN.m D. 2 KN IB 10 m Diameter=100 mm E B
SITUATION 29 A single axial load of magnitude P = 62 kN is applied at end C of the steel rod ABC. a. Determine the specific type of axial stress rod ABC is experiencing due to load P. b. Determine the stress in rod AB. c. If the allowable stress for steel is 165 Mpa, find the diameter of rod BC. 30 mm 1.2m d 0.8 m₂
2.pdf A solid aluminum shaft (2 in) in diameter is subjected to two torques as shown in Figure below. Determine the maximum shearing stress in each segment and the angle of rotation of the free end. Use G = 4 x 106 ps 200 Ibft 800 bft 2 ft 3 ft - Determine the maximum stress in the member CD if you know that the distributed load W = 40 kN/m, the diameter of member CD is 45 mm and E=200 GPa.
For the given stress element, draw the Mohr's circle and determine the principle stresses and maximum shear stress..

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Q.11 A bolt is under an axial thrust of 9 kN and transverse shear force of 5 kN. Calculate the diameter of bolt according to the theory of maximum strain energy. Take o, = 250 N/mm2, = 0.3 and factor safety = 2.8. Assume uniform distribution of normal and shear stress on cross- section.