I need the answer as soon as possible 11:32 &d步.A N O ll l2_5253461708...Class AB output stageQ.1. For the output stage shown in (Figure 1), the transistors parameters are:npn BJT's : B = 150 &VA=100 Vpnp BJT's : B = 50 &VA-60 va) Draw the transfer C/Cs for (R2 large resistor) and (R2 small resistor).b) Calculate R2 so that the maximum output limit = 8 V.c) Calculate the maximum efficiency corresponding to part - b15VR2Q1Q203R1$143kaD1- VoD2RLQ410kaVi- 15VFigure 1Q.2.The transistors of the circuit shown in Figure 2 have the following parameters:FET: VT=1V, K=0.1mA/V?, VA=15V and (W/L) is shown beside eachBJT: VA= (50V for npn and 10V for pnp) and B= (100 for npn and 40 fi) Select R to yield a quiescent drain current in Qs of 0.1 mA.i) Draw the transfer C/Cs showing all voltage limits.ii) Calculate the ina cimum efficiency correspnding to the given RL,iii) Determine the required value of (W/L)s to make Ri follow the situation of RL1.

According to our guidelines, we can solve one question at a time. And, also both the questions are…

Q.1. For the output stage shown in (Figure 1), the transistors parameters are: npn BJT's : B= 150 &VA=100 V pnp BJT's : B- 50 &VA-60 V a) Draw the transfer C/Cs for (R2 large resistor) and (R2 small resistor). b) Calculate R2 so that the maximum output limit = 8 V. c) Calculate the maximum efficiency corresponding to part-b 15V PR2 Q1 Q2 Q3 R1 143kQ D1 Vo D2 RL Q4 10k Vi 15V

Q.1. For the output stage shown in (Figure 1), the transistors parameters are: npn BJT's : B= 150 &VA=100 V pnp BJT's : B- 50 &VA-60 V a) Draw the transfer C/Cs for (R2 large resistor) and (R2 small resistor). b) Calculate R2 so that the maximum output limit = 8 V. c) Calculate the maximum efficiency corresponding to part-b 15V PR2 Q1 Q2 Q3 R1 143kQ D1 Vo D2 RL Q4 10k Vi 15V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

i need the answer quickly
What 10 Wireless Equipment items need to purchase for a daycare business building?
15. _______ is a proximity sensor that uses the principle of ‘eddy current’ to sense the presence of an object.
Estimate the length of conduit to perform the next bends. EMT will be bend using a hand bender. Provide your answer in inches (just the number) using up to 2 decimals. The picture shows two panels connected by a back-to-back 23.5" stubs EMT 3/4" 6.25 ft P
Which of the following statements about equipment grounding conductors (EGCS) is true? A. The National Electrical Code permits the EGC to also perform as a grounding electrode conductor. B. More than one EGC must be used if multiple circuits are installed in a single raceway, cable, or cable tray. C. No current should be present in the EGC during normal operation. D. EGCs are required to be decreased in size to address voltage drop.
When using an oscilloscope for testing engine management systems, what is an attenuator used for? In your answer provide an example of when an attenuator should be used. (5 - 10 words)
The contractor is controlled by?
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
The wording that I am running into with questions such as "The number of conductors required to be installed between three-way and four-way switches is " is confusing. The text is not expalining this in a way that I am understanding anything other than grounding conductor, which is optional unless I am using a metal box. So what type of "conductor" is beng discussed?
Complete the following text with words Pt100 sensors are a specific type of _____(1) detector. The most important characteristic of Pt100 elements is that they are made of _____(2) with an electrical resistance of _____(3) ohms at a temperature of ______(4) °C and temperature coefficient ____(5). It is by far the most common type of RTD sensor. The other materials with which RTDs are built are: ___(6), _____(7), ______(8). The most recommended conditioning method is reading at _____(9). Typically, a _____(10) behavior of the Resistance-Temperature relationship can be assumed.
Hey see
Why did not I find your solution to all my questions ?