Q.1) For the plate shown in figure, determine the forces in three ropes if the plate weighs 1.6 kN. 1.2m D 0.8 m 0.8 m 20.9m0.9 m C

Q: For the pair of 26-lb forces applied to the handles of the crimper tool, determine the crimping…

A:

Q: 6 m 1.5 m mi -2 mL D 3m. 2.5 m ROUND OFF TO TWO DECIMAL PLACES. The balloon shown in the figure is…

A:

Q: b) The steel Cable AB and AC are attached to the top of the transmission tower. The tension force in…

A: Given Data Length of tower is: L1=60 m length of tower to point B is L=40 Distance from B to tower…

Q: Q) Consider a weight supported by a cable as shown in figure below is equal 100 kN. Determine the…

A:

Q: Determine the maximum value of b (Ib/ft) if the roller at point A can only support upto 116 lb. The…

A: Equivalent force system is drawn Moment about A is zero due to pin joint.

Q: Determine the forces on the two members (1) and (2) as shown in .figure below

A: Let F1 be the force in member 1 and F2 be the force in member 2. Apply equilibrium equation of…

Q: * .Replace the two forces in figure below by a single force 40 lb A B 7 FT

A: Let (F) be the resultant force which acts at a distance (x) from point A. So, For equilibrium…

Q: Q2: Replace the 600 Ib force of Figure below by a force through A and a couple whose forces act…

A:

Q: Structural member AB is supported by cable BC and at A by a square rod which fits loosely through…

A: Given data To determine  a) Support reaction at A b) Cable tension

Q: Q1.) A cable system is subjected to three concentrated loads as shown. The sag at point D is…

A: To Find:The sags and .The section of cable supports the largest tension and the magnitude.Given:A…

Q: Determine graphically the forces FAB and FAC

A:

Q: Q1: Determine the magnitude of the force on the pin at A for the boom shown in Fig. 1. Neglect the…

A:

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

A: Given data as per the question The load applied at point A =440 lb

Q: Q2 / Determine the tension in cach cord shown in figure below (TA, TB, TC, TD).

A: Let 'P' and 'Q' be the intersection points of chords 'C, D' and 'A, B' respectively as shown below.

Q: Determine the angle α ,and then the tensile strength in the two cables ,Tca and Tcb, for which the…

A: To find angle alpha and tension in cable AB and AC

Q: Blocks D and E weigh 5 lbf each. Block E weighs 8 lbf. Find the sag, s. 4 ft 4 ft

A:

Q: Q1) Determine the design angle for strut AB so that the 400-lb horizontal force has a component of…

A:

Q: The suspended cylinder has a weight of 50 lb A) Determine the horizontal and vertical components of…

A: A) Determine the horizontal and vertical components of force at pin A. B) Determine the magnitude of…

Q: The figure below illustrates a hydraulic jack. a) Calculate the force F1 exerted by the operator to…

A:

Q: Q2/compute the moment of force 650 N about the rod AB. 125 mm 150 mm 150 mm 100 m 300man-

A:

Q: a) Find the tension in the string. b) Determine the normal force on the 5.0 kg block.

A: To find Tension in string normal force

Q: A 3.00 m long, 8.0 kg pole is attached to a wall by a hinge on its left side. A cable attached to…

A: To find: (a) To write the sum of forces and sum of torque equations. (b) The tension in the cable.…

Q: 40 30 43 so lb 150 b 120 lb Using summation of forces, calculate for R and angle. Make sure to…

A:

Q: The frame for a sign is fabricated from a thin, flat steel bar stock of mass per unit length 4.73…

A:

Q: A cable is loaded and supported as shown in Fig. The vertical distance vc is 4 ft. Determine The…

A: Let  Ax and Ay be the normal reaction at support ADx and Dy be the normal reaction at support…

Q: The following multi-bar mechanism is used to raise the parking space of homes. Get a degree of…

A:

Q: Q) Determine the forces on the two members (1) and (2) as shown in .figure below 60 60 30 W 10 O N

A: Mechanical Equilibrium: A body is said to be in mechanical equilibrium if it satisfies the following…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.