Q.1) Assume that the control of a bottle filling system is performed with an 8051 microcontroller. • The start and stop of the conveyor is controlled by the P1.0 pin. • The bottles are moving on the conveyor and detected with a sensor. When they arrive at the filling place, they are detected with a logical "1" signal, otherwise they are detected with a "0" signal. • A valve connected to P1.1 turns on for 10 seconds to fill each bottle. • At every X bottles, the conveyor will stop for 8 minutes and then start again. The remaining time to restart in the waiting period is displayed in minutes on the 7-segment display. • Logic "1" is detected from P1.3 during the operation of the system. Logic '0' is detected from P1.3 at the end of the shift. • At the end of the shift, the number of the filled bottles will be determined and saved in a memory location as 2 bytes. Write the required program. (Crystal Frequency:12MHZ). NOTE: X number will be taken as the last 2 digits of 59

Q.1) Assume that the control of a bottle filling system is performed with an 8051 microcontroller. • The start and stop of the conveyor is controlled by the P1.0 pin. • The bottles are moving on the conveyor and detected with a sensor. When they arrive at the filling place, they are detected with a logical "1" signal, otherwise they are detected with a "0" signal. • A valve connected to P1.1 turns on for 10 seconds to fill each bottle. • At every X bottles, the conveyor will stop for 8 minutes and then start again. The remaining time to restart in the waiting period is displayed in minutes on the 7-segment display. • Logic "1" is detected from P1.3 during the operation of the system. Logic '0' is detected from P1.3 at the end of the shift. • At the end of the shift, the number of the filled bottles will be determined and saved in a memory location as 2 bytes. Write the required program. (Crystal Frequency:12MHZ). NOTE: X number will be taken as the last 2 digits of 59

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

. Design a IC555 timer based automatic water tap mechanism with the following conditions: Water flow through the tap when it is activated through IR beam. Water flow duration is 5 seconds
(a) Figure 1 shows the image of a water heater in which it has two types of controllers, namely the Pump Control and the Temperature Control. Briefly describe the operation of each controller. Cont OFF OF Figure 1
1. In a second-order linear process control system the pressure value changes from 0 to 50 PSI values in 4 seconds with a transient period ends at 3 seconds. If the maximum overshoot in this pressure control system is 10%, Find out the peak pressure value that the system was reached to? Answer: 55 Assume that the system in the above question has a rise time of 2 seconds, Also assume that the pressure value at 0.5 sec is 5PSI. What is the pressure value of the system in PSI at 2.5 seconds? Answer: 45 The answer is given. Work for step by step solution to get the given answer.
dont use ai and please explainQ1 a) If a 16MHz crystal drives the standard 8051, what is the period of one clock pulse? b) Calculate the period (duration) to execute the instruction "MUL AB."
Ultrasonic sensors are generally used in applications that require invasive measurement of level a. true b. false
PWM is the method that; 1. Sends an encrypted message. 2. Brakes a motor. 3. Creates an equivalent analog effect from digital pulses. 4. Creates an equivalent digital effect from analog pulses. 5. Runs a motor in forward and backward.
In the following table there are different voltage measurements with a multimeter for the output of a sensor, according to said data answer the following questions. a. What is the resolution of the measuring instrument? b. Is there hysteresis? c. What kind of behavior does the instrument exhibit, linear or non-linear? Why? Reference Rising descendant 0.5 0.41 0.47 0.5 0.53 0.54 | 0.56 1 0.97 | 0.98 1 1.02 | 1.05 | 1.09 1.5 1.42 1.42 1.5 1.51| 1.58 1.58 1.93 1.95 2.03 2.05 2.06 2.08 3 2.91 2.98 2.98 2.98 | 2.99| 3.05
A switch that can conduct positive on-state current, and can block positive or negative off-state voltage is called ___. A. voltage-bidirectional two-quadrant switch B. synchronous rectifier C. single quadrant switch D. four-quadrant switch
Q. What is the voltage across the load when the push button is depressed ? Q. What would the current flow be if a short-circuit is put accross the battery terminal ?
For some program, machine A has a clock cycle of time 5 ns and CPI is 1.5 whereas machine B has a clock cycle of time 15 ns and a CPI of 1. Which machine is faster and by how much?
Which statement out of the 5 is TRUE, Explain Why (50 Words) Pulse width modulation (PWM) can be used to control the speed of a DC motor. Whichstatement is correct?1. The ratio of the ON-times (supply voltage) and OFF-times (zero volt) send to theterminals of a DC motor is proportional to the average of the motor acceleration.2. PWM can be used to modulate the magnetic width of a brush-less AC motor.3. PWM modifies the pulses sent to a motor which in turn adjust the motor torqueproportionally to the pulse ratio.4. PWM can be used to adjust the average voltage delivered by a power source.This is achieved by rapidly switching the power signal on and off. Longer on-timescompared to the off times leads to a higher average power seen by the load, e.g., aDC motor.
24)A PLC scan cycle contains each of the following operations EXCEPT A)read inputs B)perform diagnostics & communication C)execute logic D)compile installed ladder logic program