Q.1 (A) Determine the transfer function H4(s)/Qo(s) for the liquid level system shown in Fig. below. [Resistances R1, R2 and R3 are linear. The flow rate from tank-4 is maintained constant at 'a' by means of a pump.] R, Tank 1 R2 Tank 2 R Tank 3 93 Tank 4

Q: Bernoulli equation Can you please share your steps, thank you

A: V2​=17.94sft​Explanation:Step 1: Step 2: Step 3: Step 4:

Q: Engine oil at 60 ° C temperature (Engine Oil) As seen in the system in the figure, from tank A to B…

A: Given data: Temperature of engine oil = 60 0C Volumetric flow rate of oil = 5.1 m3/min Gauge…

Q: If slug flow enters a distillation column, the alternating composition and density of the gas and…

A: Distillation is a separation process in which the light hydrocarbon is separated from the heavy…

Q: (3.a) Develop a set of pi groups using W and Q as the 'king' variables.

A: 3.a Given: W is a function of D,ρ,ω and Q. W = f ( D,ρ,ω,Q) Hence the total number of variables n =…

Q: The tank below is cylindrical and has a vertical axis. Its horizontal cross-sectional area is 10 m2.…

A: The schematic labeled diagram for the given system is shown below as:   Given information:   The…

Q: Consider the flow of a fluid through the piping system shown below in Figure 1. Flow If D₁ = 4D2,…

A:

Q: velocity w, the power output W, the density p, and the viscosity u of the fluid. (a) Determine…

A:

Q: Obtain a model of a level tank of uniform cross section of area A, to which a flow resistance, such…

A:

Q: Please do a,b,c

A: (a)   The variables which are used to define the state of a system is known as state variables.…

Q: A. What is cavitation? Where does it occur in centrifugal pumps?

A: Since you have posted multiple independent questions in the same request, we will solve the first…

Q: A nozzle is a device that is used to increase the velocity of a fluid by varying the cross-sectional…

A:

Q: Consider an incompressible Newtonian fluid contained between two large parallel plates of area A,…

A:

Q: Derive the dynamic mass balance equations for the following two simple cases. Assume (i) a linear…

A: This is a system of two first order system connected in series. The cases are interacting and non…

Q: Air at 300 K and 1 atm enters an in-line tube bank consisting of 5 rows of 10 tubes each. The tube…

A: Tube banks are found mostly in heat exchangers. The tubes here are arranged in-line and are not…

Q: 1. Practically the total head of liquid at a point does not remain constant during the flow, why?

A: The total head of liquid at a point in a flowing system doesn't remain constant primarily due to…

Q: Water (density 1000 kg/m³, viscosity 1 mNs/m²) is pumped through a 50 mm diameter pipeline at 4 kg/s…

A: Given, Diameter of pipe line= 50mm Refer moody chart and explanation is given below

Q: Determine the response of the outlet temperature To of the STH to a step-change in the inlet…

A: Given data: Initial inlet temperature = 60 0C Inlet temperature after a step change = 65 0C Volume…

Q: Please solve the first, third and fourth questions by explaining how to solve them in steps

A:

Q: 3. Chapter 4: Water is steadily flowing through a three-way connector in the Figure. It enters the…

A:

Q: In a sugar-processing plant, a centrifugal pump transports cane juice from the bottom of a juice…

A: Given Juice is transport juice from tank1 bottom to tank2 bottom Difference in level of liquid in…

Q: Consider constant altitude, steady flow along a streamline with a flow that satisfies the…

A:

Q: A. What is cavitation? Where does it occur in centrifugal pumps?

A: Since you have posted multiple independent questions in the same request, we will solve the first…

Q: What is the power output -2

A:

Q: The stream function for an incompressible, inviscid flow of water is given by y = - 10x+ 2y. (a)…

A: NOTE: Because you have posted a question with multiple subparts, we will solve the first three for…

Q: 3.14.* A water tank has an inflow line 1 ft in diameter and two outflow lines of 0.5 ft diameter.…

A:

Q: what is the transfer function which relates the hight (h) to the inlet flow(E1) of the Conical tank…

A:

Q: Q.1 An airstream with Mach number of 2, a pressure of 150 kPa and a temperature of 350 K enters a…

A:

Q: Rfor the liquid-level system of figure below. q(s) Q4. Derive the transfer function The…

A:

Q: A- What are the three main branch of fluid mechanics? B- Bernoulli equation has three terms, wright…

A: Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: In an industrial heat exchanger system, the infet temperature of hot fluid is 80 °C and exit…

A:

Q: Develop the dynamic mathematical model relating the change of liquid depth h with respect to time t.…

A:

Q: 2) Both ends of the nozzle with an inlet cross-sectional area of lx10-S ft² and an outlet cross-…

A: In fluid mechanics, Bernoulli's theorem is described as the total mechanical energy of the flowing…

Q: 1)Water is pumped from a storage tank through a tube of 3.0 cm inside diameter at the rate of 0.001…

A:

Q: A step change of magnitude 3 is introduced into the transfer function Y(s) 10 X(s) 16s²+2s+0.5

A: Given transfer function: Y(s)X(s)=1016s2+2s+0.5Y(s)X(s)=2032s2+4s+1  -----(1)

Q: 1. Practically the total head of liquid at a point does not remain constant during the flow, why?

A: “Since you have posted multiple questions, we will provide the solution only to the first question…