Q.1) A ball is shot at high speed into a frictionless channel that is in the shape of a segmentof a circle with center at 0.The channel is frictionless and sits on a horizontal table top.Thefigure shown is the top view.Which of the following force(s) are acting on the ball when it is within the frictionlesschannel at position B? Explain your answers.Check all that apply.A downward force of gravity.A force pointing from O to B.A force in the direction of motion.A force pointing from B to O.Which path would the ball most closely follow after it exits the channel at C and movesacross the frictionless table top?L L L

Part (a): When the ball is undergoing motion in the frictionless horizontal segment of a circle, it…

Q.1) A ball is shot at high speed into a frictionless channel that is in the shape of a segment of a circle with center at O.The channel is frictionless and sits on a horizontal table top.The figure shown is the top view.

Q.1) A ball is shot at high speed into a frictionless channel that is in the shape of a segment of a circle with center at O.The channel is frictionless and sits on a horizontal table top.The figure shown is the top view.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1 The (aank radius of a single cyinder IC engine is 60mm and the diameter of the cylinder is somm. The swept Volume of the cylinder is Cm³
4. Consider a following figure where water goes through an oddly shaped channel. The top passage is a cylindrical tube with diameter 5 m. The bottom tube is also a cylindrical tube with diameter 10 m. 5m 30 m 100 m 20 m 10 mi a. Find the speed of water flow on the vertical tube with diameter 5 m. b. Find the speed of water flow on the horizontal tube with diameter 10 m. c. If we were to seal the horizontal tube, what is the minimum force the sealant should handle? d. What will happen to the speed of the water through vertical tube if its diameter is increased? B
A particle is moving along a curved path. At a certain instant when the slope is 0.75, ax = 2 m/s2 and ay = 3 m/s2. a. Find the value of at. b. Find the value of an. c. Find the value of aT.
3) The ME Department just purchased a new mega-drone that weighs 220 lbs and can descend autonomously to land on its own. The drone company included the graph shown below for how much force is applied to the Thrust 'T'. If the operator allows the autonomous descent when the drone has an initial downward velocity of 2 ft/s, calculate the velocity of the drone after 3 seconds. T, Ibf V = 2ft/s 260 t, (s) 5:57 PM O 57°F Mostly sunny 3/6/2022 99+ P Type here to search Del PrtScn FB Home F9 End F10 PgUp PgDn F12 F11 F6 F7 F5 F4 Esc F2 F3 F1 Backspace & @ %23 2$ % 8 4. Y U Q W
A basketball leaves a player's hands at a height of 2.20 m above the floor. The basket is 3.05 m above the floor. The player likes to shoot the ball at a 38.0 angle. If the shot is made from a horizontal distance of 6.90 m and must be accurate to +/- 0.23 m ( horizontally), what is the range of initial speeds allowed to make the basket? 0
4. The pressure in a stationary liquid depends on the position below the surface z according to p(2) pg2, where p is the density of the liquid and g is the acceleration due to gravity. A planar dam of width w separates water of depth d from air. = (a) The force exerted by the water on the dam. (b) The moment exerted by the water about the central point O of the base of the dam. d Side view 12 Top view W
The figure shows a right-angled construction frame ABC. When measured at rest, it has dimensions as follows: AB = 18.9 m, AC = 10.0 m, and BC = 16.0 m. This frame is now given a new velocity of 0.420 c, relative to Earth, in a direction parallel to AC. How long is part BC of this frame with the new velocity as measured by Earth-based engineers?
Consider a helicopter flying in a straight path at a speed of 52 m/s. The the rotor diameter is 10 m and the rotors are moving at 264 RPM (revolutions per minute). What is the maximum rotor tip speed (in m/s). Hint: Note that the rotor will sometime be moving in the direction of the flight path and at other times opposite to the flight path or at an angle to the flight path. The maximum rotor tip speed is generated when the rotor is moving in the direction of the flight path.
A ship is approaching the dock at 45 cm/s . A landing equipment was left on the dock and needs to be thrown to the ship just before it can dock. The equipment is thrown 15 m/s at 30o with the vertical from the top of the tower 8.75m above the ship deck. Compute the distance from the deck to the ship be at the instant the equipment is thrown.
Note: The following is part of a multi part question where you are asked to calculate the velocity at station 2, Pressure at station 2, and force exerted by the fluid on the bend in the x-direction. Please complete all the above steps and select the correct answers as the relevant questions arise in the quiz. Water flows through the 180 degree bend and Nozzle assembly as shown in the Figure below. Assume the assembly lies in the horizontal plane such that gravity is irrelevant (There is no height difference between Station 1 and Station 2!) Calculate the Pressure at Station 2 Hint: Having calculated the velocity at station 2, Use Bernoulli's equation to find the pressure at station 2! REMEMBER NO HEIGHT DIFFERENCE... 160 mm V2 Section (2) 300 mm V Section (1) 100 kPa %3D P1 V1 2 m/s %3D Select one:
Water is flowing at a depth of 10.0 ft with a velocity of 10.0 ft/s in a channel of rectangular section. a)If there is a smooth contraction in the channel width from 10.0 ft to 9.0 ft, calculate the flow depth in feet in the contracted section using a solver. b)If there is a smooth contraction in width from original upstream width of 10.0 feet, find the minimum width (in feet) in the contraction so that choking is prevented.