Q. In a belt transmission dynamometer, the distance between the center of driving pulley and the dead weights is one meter. Determine the value of dead weights required to keep the lever in horizontal position, if the power transmitted is 7.5 kW and the diameter of each of the driving pulley as well as the intermediate pulleys is equal to 40 cm. The driving pulley runs at 500 r.p.m.

Q. In a belt transmission dynamometer, the distance between the center of driving pulley and the dead weights is one meter. Determine the value of dead weights required to keep the lever in horizontal position, if the power transmitted is 7.5 kW and the diameter of each of the driving pulley as well as the intermediate pulleys is equal to 40 cm. The driving pulley runs at 500 r.p.m.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A 10 kg, 0.5 m radius wheel rotates with an angular acceleration of 10 rad/s/s. What is the torque ( KNm ) developed at the rim of the wheel? 2. A 10 kg, 0.5 m radius wheel running at 1800 rpm develops a torque of 50 KNm. Find the power ( KW ) transmitted by the wheel. 3. The total acceleration develop at the rim of the wheel 100 m/s/s. What is the wheel centripetal acceleration ( m/s/s ) if the tangential acceleration is 80 m/s/s ? 4. A particle moves in such a way that a = 2 s + 1 m/s/s , where t is in seconds. If the particle has moved 9 m , what is the velocity ( m/s ) at that point ?
Analyze the biomechanics of doing a finger push-up. Determine the effect of finger push-ups on the finger muscles and joints. The figure below shows the forces acting on a single finger during a finger push-up. Assume that the weight of the finger is negligible. If 0 FN lf length of finger 8: angle the finger makes with the horizontal Fm: magnitude of the finger flexor muscles lm: distance away from the finger joint to the finger flexor muscles Om: angle with respect to length of finger FN = 80 N = 6 cm = 50° От Compute Fm and the joint reaction forces (Jx & Jy) at the thumb given these parameters: If Om = 0.75 cm = 30° Fm
A winch mechanism with a handle length of 30 cm and a drum diameter of 8 cm isused to lift a 45 kg load.a. What is the VR of the winch?b. If 73.5 N of force is required to lift the load, what is the MA?c. What is the mechanical efficiency of the winch?d. How many turns will be required to lift the weight 0.85 meters?
Question 2 You want to move a hay bale to the top of a hill using a forklift. Find the minimum tractive force, P, between the tires and the ground that is required to move the hay bale. The mass of the bale is 1200 kg. Assume u, = 0.4 between the bale and the ground and between the bale and the vertical forklift platform. 30° P = 22.1 kN
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
3. Please calculate the annual electricity production of a wind farm with 20 turbines. The annual mean wind speed is 7 m/s and diameter of the blades is 20 m. If we assume power consumption of a person is 3,000 kWh, about how many people will this energy support? Annual electricity production (KWh) = K Vm³ At T Where: - - - K = 3.2 (factor based on turbine performance) Vm= annual mean wind speed (m/s) At = swept area of turbine (m2) T = number of turbines Suitable for medium- to large-scale wind turbines (> 200 m2 swept area)
A hydraulic press consists of two pistons, the diameter of the largest piston being 55% larger than the diameter of the other piston. Assuming that the hydraulic oil used for power transmission is incompressible and that a force F1 was applied to the piston with the smallest diameter, a force F2 will arise, as a consequence, to the piston with the largest diameter. The F2/F1 ratio is: a.2,40 b.0,42 c.0,32 d.6,20 e.1,55
4. A meter stick has a pivot that is located at (35 cm). On this meter stick we place 200 g @ 20 cm, 200 g @ 25 cm, 350 g @70 cm and 100 g @80 cm. The meter stick has a mass of 150 g. a. How much mass needs to be placed at 55 cm in order to balance the meter stick. b. Where will you put 500 g in order to balance the meter stick?
1) A small steel block and a magnet rest on a horizontal frictionless table. The steel block weighs 0.07N and the magnet is fixed to the table. The force acting on the steel block by the magnet is inversely proportional to the square of the distance between the steel block and the magnet. When the block is 26cm away from the magnet, the force becomes 0.145N. If the block starts its motion from rest at this position, what is the magnitude of the velocity of the block when it is 9.5cm away from the magnet?