Q) The shaft of a collar thrust bearing rotates at 200 r.p.m and carries an end thrust of 10 tonnes. The outer and inner diameters of the bearing are 480 mm and 280 mm respectively. If the power lost in friction is not to exceed 8 kW, determine the coefficient of friction of the lubricant of the bearing.

Q) The shaft of a collar thrust bearing rotates at 200 r.p.m and carries an end thrust of 10 tonnes. The outer and inner diameters of the bearing are 480 mm and 280 mm respectively. If the power lost in friction is not to exceed 8 kW, determine the coefficient of friction of the lubricant of the bearing.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A car engine has its rated output of 16 kW. The 22 maximum torque developed is 120 N-m. The clutch used is of single plate type having two active surfaces. The axial pressure is not to exceed 85 kN/m². The internal diameter of the friction plate is 0.75 times the external diameter. Coefficient of friction = 0.3. Determine: 1. The dimensions of the friction plate and, 2. The axial force exerted by the springs.
The hand brake of Fig. is used to control the rotation of a drum. The coefficient of friction between the belt and the drum is , = 0.15, and the weight of the handle may be neglected. If a counterclockwise torque of 5 ft - Ib is applied to the drum Repeat the problem for a clockwise torque of 5 ft · Ib. What happens to the system at a 4.6 in.? What does the solution mean for a> 4.6 in.? M= 5 lb-ft -12 in. 12 in
2. The power transmitted between two shafts 3.5 meters apart by a cross belt drive round the two pulleys 600 mm and 300 mm in diameters, is 6 kW. The speed of the larger pulley (driver) is 220 r.p.m. The permissible load on the belt is 25 N/mm width of the belt which is 5 mm thick. The coefficient of friction between the smaller pulley surface and the belt is 0.35. Determine: 1. necessary length of the belt; 2. width of the belt, and 3. necessary initial tension in the belt. Answer. 8.472 m; 53 mm ; 888 N
A leather belt of thickness 6 mm and width 80 mm connects two pulleys of 500 mm diameter and 900 mm diameter, their centres being 2.5 m apart. If speed of the larger pulley is 300 r.p.m, the coefficient of friction between belt and pulley is 0.25 and maximum belt stress is 100 N/cm2, determine the maximum power transmitted and initial belt tension.
Given: Q=14,361.60gpm L=1000ft D=2ft hf=12.58ft. Determine the friction (f).
AN ENGINE DEVELOPING 45 KW AT 1000 R.P.M IS FITTED WITH A CONE CLUTCH BUILT INSIDE THE FLYWHEEL. THE CONE HAS A FACE ANGLE OF 12.5° AND A MAXIMUM MEAN DIAMETER OF 500 MM. THE COEFFICIENT OF FRICTION IS 0.2. THE NORMAL PRESSURE ON THE CLUTCH FACE IS NOT TO EXCEED O.1 N/MM². DETERMINE, (1) THE AXIAL SPRING FORCE NECESSARY TO ENGAGE TO CLUTCH AND (2) (II) THE FACE WIDTH REQUIRED.
None
Q1: A flat belt is required to transmit 35 kW from a pulley of 1.5 m effective diameter running at 300 r.p.m. The angle of contact is spread over 11/24 of the circumference and the coefficient of friction between belt and pulley surface is 0.3. Determine, taking centrifugal tension into account, width of the belt required. It is given that the belt thickness is 9.5 mm, density of its material is 1.1 Mg/m³ and the related permissible working stress is 2.5 MPa.
i need the answer quickly
In a thrust bearing, the external and the internal diamaters of the contacting surfaces are 320 mm and 200 mm respectively. The total axial load is 80 kN and the intensity of pressure is 350 kN/m2.The shaft rotates as 400 rpm. Taking the coefficient of friction as 0.06, calculate the power lost in overcoming the friction. Also, find the number of collars required for the bearing.
I neee typing clear urjent i will give 5 upvotes
An open flat belt is required to transmit 50 kW from a pulley of 1.5 m effective diameter running at 300 r.p.m. The angle of contact is spread over 11/24 of the circumference. The coefficient of friction between the belt and pulley surface is 0.3. Determine, taking centrifugal tension into account, width of the belt required in mm. It is given that the belt thickness is 9.5 mm, density of its material is 1100 kg/m3 and the related permissible working stress is 2.5 MPa.