Q No. 6: A turbine is to be installed where the net available head is 180ft and the available flow will be average 900cfs. What type of turbine would you recommend? Assume the turbine is 5ft above tailwater, and its efficiency is 92%. Find the size of runner

Q: A 2-stage centrifugal pump delivers 50 gpm of 225ºF water against 200 ft head at 3200 rpm. a) What…

A:

Q: The diameter of the discharge pipe of a boiler feed pump is 4 inches and the suction pipe is 6…

A:

Q: 15. A pump delivering water at a rate of 100,000 GPM. The maximum available NPSH is 50 ft. Find the…

A: The maximum speed to avoid cavitation is 476 RPM.

Q: 3. Based from the pump performance curve below, calculate the following: a) Specific speed b)…

A: Given data Pump performance curve From the pump performance curve,  specific speed and suction…

Q: Consider a pitch-regulated, variable speed wind turbine that is 170m in diameter. The cut-in wind…

A: diameter of wind turbine (d) = 170m cut in wind speed = 4m/s rated wind speed = 12m/s cut-out wind…

Q: Еxample 3-6 A mixed type reaction turbine has D1= 3m and D1= 2.1m. Inlet and outlet Vane angle 60° &…

A: Given Data:- D1=3m D2=2.1m B1=60° t=0.3m alpha=15°

Q: 4- A Pelton wheel has a mean bucket speed of 10m/sec with a jet water flowing at the rate of…

A: Given:u=10 m/sQ=700 L/s =0.7 m3/sH=30 mθ=160°cv=0.98

Q: the jet ratio is approximately 12. Find the size of the jet, mean diameter of runner, synchronous…

A:

Q: a reaction turbine is

A: NEED TO FIND SPECIFIC SPEED ( REACTION TURBINE)

Q: what is the efficiency? what is the NPSHR? what is the motor power requirement?

A: (1):EFFICIENCY- The term efficiency can be characterized as the capacity to accomplish a ultimate…

Q: If a turbine that is to generate 15 hp under a head of 30 ft to drive a 700 rev/s generator is…

A:

Q: A centrifugal pump has the following data: pumped discharge 3m3/min, head 18m, operating speed 1210…

A:

Q: The following particulars apply to a two-row velocity compounded impulse stage of a turbine: nozzle…

A:

Q: A course in Turbomachinery. ..Lecturer: Dr.Naseer Al-Janabi 21 125 J/kg and Total to Total…

A: Fluid Mechanics: It is a branch of physics in which concerns with mechanics of fluids and forces…

Q: Home work! designed. a home with PumP and calculate the Pump How to make water into tank. How to…

A: To find:   Designed a home with Pump and calculate the Pump How to make water into tank. How to…

Q: Determine the power requirements for 3 m diameter, six-blade flatblade turbine impeller mixer…

A:

Q: To 212 F Water at 65 F flows nto a boiler at 5 gal min. It is converted to steam at 212 F Find the…

A: Given Data State 1: Saturated water, 65°F State 2: Steam, 212°F V= 5 gal/min

Q: A Kaplan turbine of 100 B.H.P. is working under a head of 5 in and running at 210 R.P.M. The…

A:

Q: The centrifugal pump speed is changed when the impeller size is constant. The initial flow is 200…

A:

Q: A Kaplan turbine produce (9 MW) under a head (7.5 m). Assume a speed ratio of (2) flow ratio (0.75)…

A:

Q: FLUID MECH Support your answer with the appropriate solution and diagram. 4. The water level in a…

A:

Q: Drive Velocity Triangle For Axial Mixed Flow For Francis Turbine.

A: Francis turbine is a hydraulic turbine that extracts energy from fluid. In this, working fluid is…

Q: h) Find for the Nozzle-Bucket efficiency, in per cent. i) Solve for the Turbine Gross efficiency. 1)…

A: For solution refer below images.

Q: 100 R, Po1 =200 psia, an :11

A: As a piece of a task on microjet motor plan and production, this paper depicts exhaustively every…

Q: A pneumatic system feeds a total of 80 m line with 5 bar pressure and 2.4 m/min compressed air. The…

A: Pressure drop is the difference between pressure at two points in a fluid carrying network.Pressure…

Q: A reaction turbine is working under a head of 10 m with an average discharge of 700 m'/min. The…

A: Given data as per question Head =10 m Average discharge =700 m3/min Overall efficiency =90%…

Q: (114m²/sec, 84.8%, 59.87°, 14.18°) The following particulars are available about a propeller…

A:

Q: Establish the reasons of being similar of two turbomachines and Explain the significances c…

A: Given question: Establish the reasons of two turbomachines being similar and explain the…

Q: If 3.9 kg metal with 92 °C temperatures is immersed into 6 kg of water at 10 °C, what will be the…

A:

Q: -Q4:- If the wind speed measured on 10 m height from the earth. What the height of wind turbine…

A: Given Data The height from the earth surface is: h=10 m The speed of the wind is: V2=5 m/s To…

Q: Solve fast with Proper Equation. 1. A centrifugal pump delivers 2.5 cfs of water against a head of…

A:

Q: Example 3-6 A mixed type reaction turbine has D1= 3m and D1= 2.1m. Inlet and outlet Vane angle 60° &…

A: Given DataD1=3mD2=2.1m

Q: Q3) Kaplan turbine A) The runner of Kaplan turbine working under dsitance of (5.5m) to produce (9…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Q3 / What would happen if the oil was replaced with water in the steam pump? Explain that.

A:

Q: 4) State briefly why a Pelton turbine is an impulse turbine.

A: In impulse turbine there is jet of nozzle or series of nozzle which converts the potential energy of…

Q: Use the pump map attached, Suppose I want to pump water at 120 gpm against a head of 10 m. a. What…

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.