Q/ In the equilibrium position shown in figure below, the uniform bar (AB) has a mass of (50 kg) and supports load (200 kg) at (A). Determine the tension (T) in the cable and reaction force at (B)? O 2.5m 2.5m 200 kg T = 6511 N, FBx = 3823 N, and FBy = : 8992 N T = 7646 N, FBx = 3823 N, and FBy = 4169 N T = 7646 N, FBx= 2000 N, and FBy = 3299 N O Non of the above

Q/ In the equilibrium position shown in figure below, the uniform bar (AB) has a mass of (50 kg) and supports load (200 kg) at (A). Determine the tension (T) in the cable and reaction force at (B)? O 2.5m 2.5m 200 kg T = 6511 N, FBx = 3823 N, and FBy = : 8992 N T = 7646 N, FBx = 3823 N, and FBy = 4169 N T = 7646 N, FBx= 2000 N, and FBy = 3299 N O Non of the above

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A1
Determine the maximum bending moment for the beam shown below. Usea = 8 ft, b= 12 ft,c = 6 ft, and w= 15 kips/ft. The reaction forces for this beam areA, = 83.1 kips and Dy = 96.9 kips. В D a b Answer: Mmax = i kip-ft
For the beam shown below, let wo = 16 N/m, W₁ dimensions are in m. 0 1 Wo ↓ = 10 N/m, and M = 16 N/m. All W₁ min 1 1 2 3 4 5 7 Figure 2 Loaded Cantilever Beam L 6 1 8 a. Find the reactions at A. b. Find the loading function q(x) using singularity functions. c. Find the shear and moment functions V(x) and M(x). M 9 m d. Determine and plot the shear diagram for the given loading conditions. e. Determine and plot the moment diagram.
Question 1 Consider the pipe segment AB that lies in the az-plane and is bent in a circular form with radius 4 m. The pipe is supported at A by an unknown support and at B with a cable BC. B' A50 4 m If the support at A can resist a maximum cou- ple moment of 1 650 Nm, determine the small- est force F that will cause the support to fail. F 6 m D 6 m
Question 4(a) The uniform bar shown in Figure 4 weighs 428 N. It is supported by a pin at A and a cable that runs around the pulley, D. It is subjected to a uniformly distributed load of 17.7 N/m and 12.5 Nm clockwise moment at E. Beam is in equilibrium position as shown in the Figure. Take a = 0.41 m and b = 2.5 m. Determine the tension in the cable and the reaction force at A, both in Newtons. w N/m 75° A ▼▼ ▼ ▼ 12.5 Nm B E 1 m 0.5 m m b Figure 4 Question 4(b) Find a truss from your neighborhood where you can take a photo safely. It does not have to be taken from the perfect angle and as long as we can see the complete truss that is good enough. One photo would be ideal but upto 3 photos can be used. Include these photos in your solutions for this question and based on these photos draw this 2D truss (exact dimensions are not required) with the supports too. Comment on the possible loads and their locations that may be applied to the truss. Discuss the assumptions that you have to…
Need asap
The cargo box as shown weighs W = 1200 lb. The force P = 800 lb is just sufficient to lift the box off the floor. The 2-D concurrent force system of the joint O is shown as well. Using the equilibrium equations: ∑ ???= 0 ; ∑ ???= 0, 1) Determine the tension force in the cable T;2) Determine the corresponding value of β
do asap
4 pls have fbd
The frame shown supports a load W DE 1000 lb through the cable that passes through 3 pulleys and at the end is attached to a frame, also supports the distributed loads ω1 = 100 lb / ft; ω2 = 60 lb / ft and ω3 = 50 lb / ft. Determine: 1. Reactions at supports A and E. 2. Forces acting on bar ABCDE, show the results in graphical form of the beam. That is, you must make the simplified free-body diagram of the loads that act only on the horizontal element. 3. Make the shear force and bending-moment diagrams for the entire beam. The geometry and load data are as follows: see the geometry and load in the images. Clarification: THE CABLE GOES BEHIND THE FRAME AND THE CONTACT IS ONLY WITH THE PULLEYS AND THE GRIP TO THE FRAME (WALL).All pulleys have the same radius.