Q/ How many bricks you need to build a room and roof with interior dimensions of (5m x 4m). The height from the standard tiles to the roof is (3m). The thickness of walls is (0.24 m). The room have one door its dimension (1m x 2.1 m) and one window (1.5 m x 1.5 m). The roof is constructed from brick. The number of bricks in roof is 58/1m?. Use center line method. Also find the total volume of cement mortar.

Q/ How many bricks you need to build a room and roof with interior dimensions of (5m x 4m). The height from the standard tiles to the roof is (3m). The thickness of walls is (0.24 m). The room have one door its dimension (1m x 2.1 m) and one window (1.5 m x 1.5 m). The roof is constructed from brick. The number of bricks in roof is 58/1m?. Use center line method. Also find the total volume of cement mortar.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A timber wall 75 mm wide, 75 mm deep and 3.50 m high is assumed to be fixed at the top and bottom. It is subjected to uniformly distributed load of 388 N/m acting along the weaker axis of its entire height. The wall is made up of Apitong wood with 80% stress grade with properties as shown: Bending and tension parallel to the grain = 16.5 MPa Modulus of Elasticity in Bending = 7310 MPa Compression parallel to the grain = 9.56 MPa Compression perpendicular to the grain = 2.20 MPa Compute for the following: a) Allowable compressive stress b) Allowable bending stress c) Maximum axial load %3D %3D %3D
QI/ Choose the Correct Answer? 1. Queen closer may be placed A. In header course B. In stretcher course E In any position. C In header course next to first brick D In stretcher course next to first brick 2. The foundations are placed below ground level, to increase A. Strength B. Workability C. Stability of structure D. All the above. 3. The 11 cm x 7.5 cm side of a brick as seen in the wall face, is generally known as: A. Stretcher C. Face Е. Неader в. Front D. Side 4. Buildings can be classified according to construction Method to: A. cast in situ and Pre cast B. Nonstructural Buildings C. Lightweight structures 5. The Ribbed Slabs are known: B. Short Span A. Long Span C. Intermediate span
Please solve quickly, guess material
Q: In an attempt to construct a precast building, the architectural in engineer proposed a 400 mm width for a simply supported single reinforced concrete rectangular beam. Design this beam and assume your design that: fc = 25 MPa, fy = 400 MPa, L = 6 m, D.L = 160 kN/m (include self-weight), L.L = 150 kN/m, concrete weight = 24 kN/m3, bar diameter of 25 mm for longitudinal reinforcement and bar diameters 10 mm for stirrups.
ll中国移动 4G PN © 11:50 PM 75% 4 A spiral column with the diameter of 500 mm has the effective height of lo-4.0 m. The axial compressive strength of the concrete is f. - 14.3 N/ mm. The longitudinal steel bars are 6 22 with the yield strength ofS, - 360 N/mm. The spirals are 10@50 with the yield strength of f,- 270 N/ mm². If the concrete cover is 30 mm thick, determine the ultimate compressive capacity of the column.
A floor panel 3 4 m wide and 12 m long is intended for a vibratory machine in a factory. The concrete to be used has a strength of 27.6 MPa (whose density is 1800 kg per cubic meter) and reinforcement used has yield strength of 280 MPa Determine the minimum thickness of slab if the panel is cantilever
A concrete wall is 4m high, 6m long, and 4 in thick. Determine the number of 4kg. cement, sand and gravel required using concrete class AA.
Q- If the actual thickness of a brick masonry wall is 19 cm, its effective length is 2.70 m, its effective height is 2.82 m and its code-specified stiffening coefficient is 1.2, then, for design considerations, the slenderness ratio of the wall will be taken as..
The size of the brick is 190 mm x 90 mm x 90 mm and the mortar is 8 mm thick with a ratio of 1: 4. Calculate the number of bricks for 1 meter cube:
Please show all intermediate steps such as free body diagram, equations used, problem setup, and etc so that your approach can be easily followed
Kindly write the COMPLETE solution NEATLY. Thank you
3. a) Use diagrams to explain the steps and procedure of block and brilaving. b. Explain the various bond methods used in constructing a wall. c. Roughly estimate the volume of mortar and quantity of materials required to construct a 150m² wall, using a 1:4 mortar mix ratio.