Q/ Design the rectangular duct system shown in figure below using equal friction method with frictional pressure drop of 1 pa/m. and allowable height is 300 mm assume the dynamic loss coefficient for elbow and exitas =1. 0.6 m /s 0.6 m'/s D 2m 2m 2m F 2m Fan 2m E B A 5m K 2mH G 2m 2m 2m 2mI 0.6 m/s 0.6 m /s Mechanical Engineering Department Subject : AC and Refrigeration

Q/ Design the rectangular duct system shown in figure below using equal friction method with frictional pressure drop of 1 pa/m. and allowable height is 300 mm assume the dynamic loss coefficient for elbow and exitas =1. 0.6 m /s 0.6 m'/s D 2m 2m 2m F 2m Fan 2m E B A 5m K 2mH G 2m 2m 2m 2mI 0.6 m/s 0.6 m /s Mechanical Engineering Department Subject : AC and Refrigeration

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

40 L/s of 20C water (ν = 1.007*10^(-6) m^2/s). Flows through 1,200 ft of6-in diameter new steel pipe with ks = 0.0002 ft. The friction loss must be:
Q2. Flowrate of water through bend pipe (90°) is 0.21 m/s. The pipe diameter at the inlet is 150 mm and the outlet diameter is 75 mm. The outlet is higher than the inlet by 2 m. Frictional losses in the pipe is equal a loss factor of 0.5 applied to the inlet velocity head. The pressure head at the inlet is 8.6 m and the volume of water in the bend is 0.6 m?. Calculate the resultant force and its direction.
Please solve showing sketch please
A homogeneous rectangular gate AB 6.1 ft wide and 10 ft long. Friction in the hinge is negligible. Find force acted on surface AB? L = 5.06 ft 60 A water L B hinge Answer:
8.4
SITUATION #2 Determine the maximum diameter of the cylinder tank if the internal pressure is 127 kPa. Given the allowable stresses for longitudinal 140 MPa and tangential 100 MPa. L = 10 m
Water is flowing steadily in a horizontal elbow and nozzle combination shown in the figure. The gage pressure at section (1) is 100 kPa with inlet velocity of 2 m/s. At section (2) the water exits to the atmosphere. Neglecting pipe weight, determine the magnitude and direction of the x and y components reaction forces exerted on the flanges to withstand this flow. 160 mm y section (2) 300 mm V1 -> section (1) P, = 100kPa V, = 2m/s
Air at 30°C flows through a 70 m long, 2 cm x 2 cm rectangular cross section pipe as shown in Figure 1(b). The flow is laminar flow and centerline velocity is 2 m/s. If the angle of pipe measure from horizontal plane is 35º, determine : (iv) wall shear stress; (v) shear stress at 1 cm from the center of the pipe; and (vi) power required to maintain this flow.
25 pts A circular door having a diam. of 3m closes a horizontal duct from a small diam. as shown. The center of the door is 4.5m below the liquid surface. Assuming the specific gravity of liquid is 0.9o. Compute the following: a) hydrostatic force acting on the door, [ Select ] b) the location of the center of pressure from the centroid of the door, [ Select ] c) the force at the bottom of the gate to maintain equilibrium if it is hinged at the top. [ Select ] 4.5 m 3m
If the friction headloss is significantly changing in a pipe flow, which of the following is most and first affected?Group of answer choices A. pressure head B. elevation head C. total head D. velocity head
... "H" hinge water A 1m 40KN 1.5m In the figure shown, find the depth of water "H" if the force at the bottom of the gate is 40KN to make the system equilibrium. The rectangular gate which is hinged at point A has a dimension of 1m depth and 1.5m width. A) 5.77 m B 6.27m 5.27 m No answer among the choices E 6.77 m
Solve the pipe network shown in the figure. The 12 in and 16-in are of new cast iron, while the 18 and 24 in are of average concrete. Assume n=2.0 and use the values of f from figure 8.11 for complete turbulence. If the pressure at h is 80 psi, find the pressure at f