Q// Consider the system0;(s)kmkakp0,(s)s(Tms + 1)radk, = 2 v/rad , km= 201v , Tm = 0. 1 secsecO; = 40 u(t) degreeCalculate: -a. The value of ka for underdamped response and percent overshoot =40%b. tn1 the time for the first peak for the response in part ac. The value of ka for critically damped responsed. The value of ka its required that the damping ratio 3 = 1.5а

Answered: Image /qna-images/answer/a5454475-fc57-4db7-b10f-dc6b5c810044.jpg

Q// Consider the system 0;(s) km kakp 0,(s) s(Tms + 1) rad kp = 2 v/rad , km = 20 , Tm = 0. 1 sec sec 0 = 40 u(t) degree Calculate: - a. The value of ka for underdamped response and percent overshoot =40% b. tp1 the time for the first peak for the response in part a c. The value of ka for critically damped response d. The value of ka its required that the damping ratio 3 = 1.5

Q// Consider the system 0;(s) km kakp 0,(s) s(Tms + 1) rad kp = 2 v/rad , km = 20 , Tm = 0. 1 sec sec 0 = 40 u(t) degree Calculate: - a. The value of ka for underdamped response and percent overshoot =40% b. tp1 the time for the first peak for the response in part a c. The value of ka for critically damped response d. The value of ka its required that the damping ratio 3 = 1.5

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3) Pina the . OTFT of ) x(n)= a pmd
A Phase Modulator has a phase deviation constant, Kp = 35°/V. The carrier signal is ec = 8 cos2n(800k)t, volts and the modulating signal is em = 5 sin2r(2000)t, volts. a. What is the equation of the PM signal? b. What is the maximum phase deviation? c. what is the amount of deviation in the carrier phase angle at t = 160µs?
E5.17 A closed-loop control system transfer function T1(s2)has two dominant complex conjugate poles. Sketch theregion in the left-hand s-plane where the complex polesshould be located to meet the given specifications.
I need the answer as soon as possible
Explain the principle of 'source transformation'.
A shunt generator supplies a 30kW load at 215V through cables of resistance, R = 110mn. If the field winding resistance, Rf =680 and the armature resistance, Ra =45mn. Determine the following below: The terminal voltage is, The e.m.f. generated in the armature is,
a) Sketch and explain the root locus curve. b) Calculate the separation point from the real axis and the gain here. c) Calculate the virtual axis cut-off points and also the gain values at this point. d) Determine and explain the stability range.
A plot of the exponential spectrum of the signal x(t) = 4 sin(200πt) +12 sin(1000 πt) will have a peak amplitude of _______ at -500Hz as well as a bandwidth of ______Hz.. Single choice.
i need the answer quickly
1. Suppose the MOSFET drawn has Vth = 1 V, and ID = 1 mA when Vov = 0.5 V. Vin Vin VDD = 5V I R₂ = 5 kn Vout Vs.VD. VDD t t (a) Calculate the Vin values that lead to off, linear, and saturation modes respectively. Indicate the boundaries of these regions on the Vin plot. (b) Draw a suitable 100 mV amplitude sinusoid for Vin that keeps the MOSFET working in saturation mode. (c) Draw three time-domain waveforms for VS, VD, VDD that correspond to Vin from part (b).
1. If we add a Zero into a system: I. The gain slop will be increased by 20db/decade at its corner frequency. II. The gain slop will be decreased by 20db/decade at its corner frequency. III. Gain will not be affected. IV. None of the above. 2. If we add a Pole into a system: I. The phase will be increased by 90 degrees. II. The phase will decrease by 90 degrees. III. Phase will not be affected. IV. None of the above. 3. In systems, the Integrator add slop to the system gain equal to: I. 20 db/decade. II. -20 db/decade. III. 0 db/decade. IV. None of the above 4. The purpose of the Lag Compensator is: I. Improve the study state response of the close system. II. Speed up the transit response. III. All the above. IV. None of the above. 5. In the Lead Compensator: I. Z > P. II. Z < P. III. Z = P. IV. None of the above.
Solve all the sub parts.. I will rate