Q: A simple manometer is used to measure the pressure of water flowing in a pipe line. Its right limb is open to the atmosphere and the left limb is connected to the pipe. The center of the pipe is in the level with the mercury in the right limb. Determine the pressure in the pipe, if the difference of mercury levels in the two limbs is 100mm

Q: figure 5 shows a manometer being used to indicate the difference in pressure between points A and B…

A: Question is based on the concept of manometer. A manometer is given in the questioncontains water…

Q: Air For the setup shown, a manometer was attached from a tank into a pipe with liquid (SG=0.95).…

A: Given data in question  Depths Oil of specific gravity 0.95 To find out  Absolute pressure at A Note…

Q: Two pipes A and B contain water and are connected by an inverted manometer as shown in figure below.…

A:

Q: Water GLYCERIN, SG = 1.26 Pipe 30mm 3mm

A:

Q: Question 2. The manometer in the figure is used to measure the pressure difference between two…

A: ρ = density of water = 1000 kg/m³ g = acceleration due to gravity = 9.81 m/s² h = height difference…

Q: Calculate the capillary effect in mm in a glass tube of 4 mm diameter, when immersed in (i) water,…

A: Given data : Diameter (d)=4 mmDensity of water (ρW)=998 kg/m3Surface tension of water (σW)=0.073…

Q: A manometer is attached to a water tank as shown in the figure. Find the pressure at the interface…

A:

Q: vessel at its o r is mercury, - figure shows the vessel is e n, find the rea her the readi 0.8. SG…

A:

Q: Current Attempt in Progress A piston having a cross-sectional area of 0.35 m² is located in a…

A:

Q: pressure of air in the pipe

A: P=ρgh at any point Given h1=0.33mh2 =0.36mh3 =0.20m h4=0.50m h5 =0.10m h6 =0.30

Q: 3. A differential manometer is attached to two tanks, as shown in figure. A) Calculate the…

A: The objective of the question is to calculate the difference in pressure between two chambers, the…

Q: A flow rate measuring device is installed in a horizontal pipe through which water is flowing. A…

A: Given  Specific weight of Gage fluid = 112 lb/ft3

Q: i) What is the gauge air pressure in the tank at Point 1?

A:

Q: A tank is fitted with a manometer on the side, as shown. The liquid in the bottom of the tank and in…

A:

Q: A mercury Manometer is attached to a pipe having suction pressure. The right limb is open to the…

A: Right limb which is open to atmosphere as per given data : For equilibrium condition a) Difference…

Q: A flow rate measuring device is installed in a horizontal pipe through which water is flowing. A…

A: Specific weight of fluid in manometer, γm=112lbft3The pressure drop between two taps, δP =0.7lbin2

Q: -oil(sg.30.85) 680 mm 1700mm water

A:

Q: Air discharges from a 2-in.-diameter nozzle and strikes a curved vane, which is in a vertical plane…

A: D = 2 in  = 22.5o  = 7 in or 0.583 ft

Q: A: Derive an expression to determine the hydrostatic force and the centre of plane submerged inside…

A:

Q: 9. For dynamic fluid motion in a pipe, the pressure measurement cannot be carried out accurately by…

A:

Q: 3. Figure 3 shows a manometer being used to indicate the difference in pressure between two points…

A:

Q: a manometer is a device that measures pressure. a common simple manometer consists of a U shaped…

A:

Q: AIR; PRESSURE=1.0 PSI OIL SG=0.82 MERCURY- LIQUID X SG=4.0

A: Given  Deflection from the gauge liquids= 800 mm  Height of mercury= 450 mm  Oil specific gravity =…

Q: (Bernoulli/continuity/Pitot tube) Two Pitot tubes and two static pressure taps are placed in the…

A:

Q: Determine the capillary rise (in cm) in a glass tube of radius 0.25 mm that is immersed vertically…

A: Given data : Surface tension (σ)=0.0725 N/mRadius (r)=0.25 mmAssume Angle of contact (θ)=0∘

Q: Q1 A U-tube manometer is used to measure the pressure of oil of specific gravity 0.85 flowing in a…

A:

Q: the fluid in the manometer while oil (S = 0.93

A:

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.