Homework Help is Here – Start Your Trial Now!
Engineering
Chemical Engineering
Q: A production section in a well was planned to be drilled to a depth of 12000 ft using 12.25" hole size. 9 5/8" casing has to be run and cemented in this section. There are two casing types available as per the specifications shown in the table below. Yield P OD ID Length Po Casing No. Grade psi in in in Ft psi psi 1 К-55 55,000 9.625 8.535 0.545 40.0 5450 5130 2 C-75 75,000 9.625 8.279 0.673 40.0 9177 7570 From previous experience it is found that production casing design depends mainly on collapse pressure. Design safety factor for collapse was set to be 1.3. Casing has to be cemented to the top using 16.8 ppg slurry. Cement slurry will be displaced using fresh water. From the above information how many joints of each casing should be used to insure as an economic selection? Discuss all your calculation steps and your selection.

Q: A production section in a well was planned to be drilled to a depth of 12000 ft using 12.25" hole size. 9 5/8" casing has to be run and cemented in this section. There are two casing types available as per the specifications shown in the table below. Yield P OD ID Length Po Casing No. Grade psi in in in Ft psi psi 1 К-55 55,000 9.625 8.535 0.545 40.0 5450 5130 2 C-75 75,000 9.625 8.279 0.673 40.0 9177 7570 From previous experience it is found that production casing design depends mainly on collapse pressure. Design safety factor for collapse was set to be 1.3. Casing has to be cemented to the top using 16.8 ppg slurry. Cement slurry will be displaced using fresh water. From the above information how many joints of each casing should be used to insure as an economic selection? Discuss all your calculation steps and your selection.

Introduction to Chemical Engineering Thermodynamics
Introduction to Chemical Engineering Thermodynamics
8th Edition
ISBN:9781259696527
Author:J.M. Smith Termodinamica en ingenieria quimica, Hendrick C Van Ness, Michael Abbott, Mark Swihart
Publisher:J.M. Smith Termodinamica en ingenieria quimica, Hendrick C Van Ness, Michael Abbott, Mark Swihart
Chapter1: Introduction
Section: Chapter Questions
Problem 1.1P
See similar textbooks
icon
Related questions
Question
Q: A production section in a well was planned to be drilled to a depth of 12000 ft using 12.25" hole size. 9 5/8" casing has to be run and cemented in this section. There are two casing types available as per the specifications shown in the table below. Yield OD ID t Length P P er Casing No. Grade psi in in in Ft psi psi K-55 55,000 9.625 8.535 0.545 40.0 5450 5130 2 С-75 75,000 9.625 8.279 0.673 40.0 9177 7570 From previous experience it is found that production casing design depends mainly on collapse pressure. Design safety factor for collapse was set to be 1.3. Casing has to be cemented to the top using 16.8 ppg slurry. Cement slurry will be displaced using fresh water. From the above information how many joints of each casing should be used to insure as an economic selection? Discuss all your calculation steps and your selection.
Transcribed Image Text:Q: A production section in a well was planned to be drilled to a depth of 12000 ft using 12.25" hole size. 9 5/8" casing has to be run and cemented in this section. There are two casing types available as per the specifications shown in the table below. Yield OD ID t Length P P er Casing No. Grade psi in in in Ft psi psi K-55 55,000 9.625 8.535 0.545 40.0 5450 5130 2 С-75 75,000 9.625 8.279 0.673 40.0 9177 7570 From previous experience it is found that production casing design depends mainly on collapse pressure. Design safety factor for collapse was set to be 1.3. Casing has to be cemented to the top using 16.8 ppg slurry. Cement slurry will be displaced using fresh water. From the above information how many joints of each casing should be used to insure as an economic selection? Discuss all your calculation steps and your selection.
Expert Solution
steps

Step by step

Solved in 4 steps with 1 images

SEE SOLUTIONCheck out a sample Q&A here
Blurred answer
Recommended textbooks for you
Introduction to Chemical Engineering Thermodynami…
Introduction to Chemical Engineering Thermodynami…
Chemical Engineering
ISBN:
9781259696527
Author:
J.M. Smith Termodinamica en ingenieria quimica, Hendrick C Van Ness, Michael Abbott, Mark Swihart
Publisher:
McGraw-Hill Education
Elementary Principles of Chemical Processes, Bind…
Elementary Principles of Chemical Processes, Bind…
Chemical Engineering
ISBN:
9781118431221
Author:
Richard M. Felder, Ronald W. Rousseau, Lisa G. Bullard
Publisher:
WILEY
Elements of Chemical Reaction Engineering (5th Ed…
Elements of Chemical Reaction Engineering (5th Ed…
Chemical Engineering
ISBN:
9780133887518
Author:
H. Scott Fogler
Publisher:
Prentice Hall
Process Dynamics and Control, 4e
Process Dynamics and Control, 4e
Chemical Engineering
ISBN:
9781119285915
Author:
Seborg
Publisher:
WILEY
Industrial Plastics: Theory and Applications
Industrial Plastics: Theory and Applications
Chemical Engineering
ISBN:
9781285061238
Author:
Lokensgard, Erik
Publisher:
Delmar Cengage Learning
Unit Operations of Chemical Engineering
Unit Operations of Chemical Engineering
Chemical Engineering
ISBN:
9780072848236
Author:
Warren McCabe, Julian C. Smith, Peter Harriott
Publisher:
McGraw-Hill Companies, The
SEE MORE TEXTBOOKS